Search results

I recently had a 8-point roll cage installed in my 68 mustang coupe. It is very similar to a 6-point with two bars connecting to the floor near the pedals, two connections for the loop behind the front two seats, and two bars that run through the rear speaker openings to connect to the rear...

I just completed the install of my new 408 storker. As expected I am having extreme problems with hooking it up. My current setup on my 68 Mustang Coupe is the following: 1. 9", 3:50 gears with open differential (soon to be a Detroit Locker, 4:11) 2. Rancho 9000 series, 9-way adjustable rear...

I'm installing a 408 stoker in my 68 stang. It has a cam with over .600 lift so it should thump pretty good. My current exhaust system is a custom bent 2-1/2" pipe with x-pipe and dual 40 series flowmasters dumped out back. I want an exhaust system that will sound mean as hell and be as loud...

I have one of these shifters installed on a C4 tranny in a 68 mustang. The first installation was done on my old trans (24 spline) by a trans shop. Just recently I did a swap myself for a 26 spline C4. Unfortunately I did not take out the old trans to see how the shifter was hooked up to the...

I have a 68 mustang coupe with a stock driveshaft and I was wondering what would be the torque limit for that shaft. I am running a 408W stroker with a C4 and a 9" with 4.11 gears. I also run MT ET Streets. I would estimate the torque well above 500 ft/lbs currently.

Will a 1967 mustang convertible rear seat fit a 1968 mustang coupe rear seat? I am in need of a new rear seat for my 68 coupe. I found this one on ebay...what do you think, how much should I bid to...

I need a 9 inch 3rd member rear end, 28 spline, preferably a 4:11 or 3:73, must be posi. Willing to trade 9 inch, 28 spline, 3:50 open rear. email me at [email protected]

I purchased brand new Edelbrock Performer IAS Monotube shocks for my 68 mustang last fall with the Grab-A-Track suspension kit from Mustang Plus. I have 2 rear shocks and 2 front shocks. I never installed the shocks last fall or over the winter, they just sat in the garage. This past week I did...

I had wrote in a previous thread that I was building a 10 sec 68 mustang and that my engine builder is using stock 1971 351W heads and is polishing and porting them. He is increasing the valve size I assume (I don't know the specifics). Some of you spoke of some concern that it is not possible...

I am about to purchase subframe connectors for my 68 coupe. I was wondering if it would be better to get the bolt-on or the weld-on subframe connectors. Also, what brands are the best?

I am in need of a rear back seat for a 1968 ford mustang coupe. Used is fine but must be in good shape (please provide pictures). Color must be black. I need both the bottom and the top pieces.

I am building a 408W that is going to be making around 500-600hp. I have a rebuilt 68 C4, 26 spline tranny with high performance clutches and a B&M shift kit. My engine builder tells me that pre 1970 C4's are junk and I need to get a 70's C4 to handle the power because of the bigger input shaft...

I was using a cutting torch under my car and a few sparks some how made its way into the interior and caught the backseat's padding on fire. I didn't notice it right away until the interior filled with smoke. There isn't any fire damage, just smoke damage. I stripped my interior and I'm going to...

I am building a 408W stroker that will make 600hp. I will be running 4:11 gears in a 9" posi with a 3500rpm stall through a C4. I have intalled GrabaTrak suspension on the car with 4 1/2 leaf springs, Edelbrock IAS shocks all around, 620 lowering springs in the front (1" drop), 1" sway bar in...

I am new to Stangnet and this is my first post. I have been building my 68 mustang since I was 16 and now that I am out of college and have the money I am finishing it. I just contracted a local engine builder that specializes in ford performance engines to build me a 408 stroker. The engine...