Search results

I now have to change the pinion seal on the diff...I went back to the gu y that did rear end for me and told me to mark the nut and count the turns that it takes to remove,and put back same exact place and use loctite and silicone to assure it stays in place.is this correct?

is there suppose to be play when the car is in gear or neutral?TKO600 is whats in there with a Detroit locker.I can go under there and grab d/s and turn it about an 1/8th turn maybe a little less.My issue here is it makes some noise(bang or clunk) if I don't shift smooth enough. is it a...

I have a 88 notch 12pt cage ,thru floor subs,10gal cell,a1000 pump #10feed#8return,detroit locker 4.10's,33spline mosers/w c clip elim.TKO600, aluminum d/s,275/60's on 15x10's in rear and skinnys up front.eibach drag springs with comp shocks out back.full front suspension with tube front end and...

fuel cell gauge install?I bought a fuel sell with the Ford fuel sender.How do I hook up the sender?I messed around with all the wires can't seem to figure it out.Sender has two posts on it (S)sender (G) ground.The factory plug I believe has a fat red wire i'd figure was the pump,yellow wire,and...

I just got my car up and running.my pump is hooked up to a fuel relay/buzz circuit breaker so im sure its installed correctly.Now then I get on the car half throttle and come to a stop it sounds funny it don't sound like its normal loud hummmm..its more like a loud grinding noise or something.I...

How much noise is to much noise.This is my first locker,and man to me its noisy as a mofo.Somtimes it sounded like a ratchet(clicking) all the way down the block till I gave it a little gas then CLUNK!

I been on a build not for over two years and its time to start her up...I hear this box under driver side dash clicking(located on the steering column brace).There is a relay missing on a wire near the computer its a red/black plug where a relay would fit.could that be the problem?I don't...

I been coming to an end on my build,and the most freak thing happens.I was turning the nut on the egr (smaller stud)and it breaks off in my fingertips I could hardly believe it.I'm glade I had a buddy to witness this freak assurance.Anyway,What size is the fine threaded end of the smaller egr...

can someone save me the hassle tomorrow and get me a gator back size for this setup http://www.powermastermotorsports.com/ford_bracket_732.jpg

I did 3 g swap and I have a single throw single throw switch.what do I do with the two blk/org wires going to alternator.not one talks about them at all.im stumped.I don't have motor in car yet to try different things,but would like to know before hand. please help and thanks in advance. kj

I just installed my upr k member/a arms and qa1 coil overs.The bottom of the qa1 strut is not allowing me to turn the hub to the inside of the car both sides(binding on the a arms).Whats the problem!!!.I noticed the bottom of the strut has a threaded nut(thats in the way)and is not screwed all...

need the carpet where the 3rd brake light goes. lets see whats out there

190+shipp pm me for any more questions. parting car out for Christmas(Merry Christmas to me huh)..hurry b4 its gone.

i was at junk yard yeasterday and seen a 92 frod pickup with a Mustang Holley EFI Intake Manifold EGR Power Band 2000-6500rpm Lower Manifold Kit 50 State Legal Polished for a lower intake is this an aftermarket intake or did they come with this..same runner design.but i believe it was stamped...

100.00 + ship.very nice.parting out car due to money issues...:( my loss is your gain [/IMG] [/IMG] [/IMG]

will that work ?

I thought I can get the UPRs to fit my qa1 k member....that didn't happen let me know what I can do...this sux

I bought a used set of Upr front control arms and both boots are tore up.possible I can purchase these same boots somewhere else?maybe an aftermarket boot that will fit these. kj

I just purchased a qa1 tube front K member.How do I go about purchasing the springs?165?150?225? ect......fill me in please Kevin

What is the difference in differential covers?The only thing I noticed is on the trickflow differential the fill hole is drilled above the half location,and on he Moroso its under the center.??less fill capacity I dono any input? Kevin