Search results

Figured I’d share this super cool car I just finished up . Holley term x install on this cool clean 90 my buddy has . It’s a gt40 headed / intake with probably a b cam deal . 3.55s and full MM suspension. In prep for a blower I went ahead and put the Holley in . This car I was tasked with...

So I have this 90LX I wire tucked that didn’t run when it got here . Cranked like a dead battery . Long story short the battery ground in the trunk was no good so I fixed this . I was not the one who relocated it originally . Car runs but won’t idle for anything breaks up etc . 306 ...

Do any of you know where or know of a 3g 6 rib alternator pulley that is 2.75 inches . I know a 94-95 is 2 1/8 . 96-98 v6 is 2.5 inches . I’m looking for something that is 2.75 . I am looking to put my custom asp 8 inch blower pulley with my 6 inch acc drive to get my water pump moving more...

Guys with Auto transmissions - what is your preferred temp sensor location ? Would you prefer a bung welded in the pan and the sensor in the pan fluid ? Or have a sensor on the return line coming from the cooler right At the transmission . Edit . Remote cooler only . This doesn’t run through the...

If you guys are bored , most of you know I’m laid up but check it out . Neil Van Opp happens to be a friend of mine who I met through my friend Roland in the video . Tony Defeo , ask Bernie Golick , Lee Rutter . Cool little history video and one bad ass 1,xxx mile coupe View...

So I believe they are , but does anyone know if the 4cyl auto and the 5.0 aod trans harness are pinned the same for the NSS and rev lights ? More specially at the trans side of the connector Thanks .

For Sale - 15k 438cu in Windsor 9.5 Deck DART iron eagle . Eagle crank GRP rods Diamond pistons with coated skirts Harland sharp shaft mount rockers with BBC trunions Isky Red Zone bushed lifters Brian Freezy “ Freezy 74” Custom solid roller cam Jesel belt drive Trick Flow...

Located in Howell NJ . Comp Custom Grind by Brian Freezy This was going on my new combo but after Brian and I spoke I decided I wanted to do something a little more aggressive . This came out of my friend Ryan’s SN95 which had been 8.8x at 3500lbs with an AOD and YsI . I do not have the cam...

Canton T sump road race pan for 302 . Pan was 450 or 475 new . Used it for due to the ground clearance it had . Works with stock k member and 1 3/4 Long tubes . Pan is setup for turbo or blower -8an oil return on pass side . Comes with pan , dipstick , and pickup (not pictured ) Pan has been...

Kooks 1 7/8 to 3 inch slip on collectors . Stainless steel. Only reason for sale is the header flange pattern does not work with my heads. Has a 3 in bolt spacing header flange for AFR Renegade, Dart , Canfield or Windsor Senior Heads. 700 obo would prefer not to ship but can at buyers cost.

This is the standard Vortech v1 bracket setup . Powder coated Black. 250 obo plus shipping Comes with 90 percent of the hardware . Just add a blower and go. This bracket is trimmed and will fit a YSI . Some blems but cleans up nice . You would need a smog delete pulley and the serpentine...

Anderson belt tensioner for v1 bracket setup . A must for any standard bracket belt setup honestly . Only selling due to going renegade brackets . 50 bucks plus shipping. Located in SI New York

For Sale - Summit 70mm Throttlebody. No issues at all made over 700hp with it. 100obo shipped. Located in S.I New York.

So with all good. Comes something that needs to be fixed right ? Starter hung up on me last night when I ran home for dinner from work. I shut key off and it just kept cranking away . I have a mini stArter . I pull the power at battery it stops . I turn around and jump both posts at the sol...

Calibrated for 60lb injector blower car . Only removed due to going standalone . -220shipped

650 plus shipping . Unit is polished and does show nice but is not show quality by any means . Seals are good no oil leaks , no shaft play . Had it on my car 2 seasons . Made 581 hp to the tire with a 2.95 and 6.7 lower . Previous owner said the blower had been rebuilt but I never checked on...

So I started the 5 Lug swap journey this morning . I have an issue . Axles in with NRC brackets the caliper bracket is not even close to centered . I loosens up one side to show how much it has to come over . What do you guys thing ? Axles not in all the way ? Maybe moser didn't machine the...

. Suggestions would be great! :nice: Sent from my iPhone using my fingers while my auto correct makes me seem illiterate

Driving last night . Do a small pull with the car no big deal car is running 178-180 . It has a 180 stat the air was real Crisp and cool last night . Get off highway cruising through The streets back to my garage . I notice the temp creeping up . Creeps To 200 on the gauge . My Pms is reading...

So I am battling an issue that is sporadic . I had an issue where I was seeing my tps percentage drop off on my Pms if I held my foot to the floor . So I replace the sensor all is good . Fire the car up after my tune session and I get no response from the sensor . I squeeze the plugs make sure...