I jsut picked up a E cam for cheap and have thought about chaging it out this weekend its going in my 331 w/afr 185 heads, holley systemax instake, t-5, 3.55 gears. Was really hoping for some more low end torque. what do you think?
I recently bought some seats that I was a little sceptical about. After reading other reviews i went ahead and gave them a shot. I was very happy and pleased with what I recieved. At 319 a pair they were very nice seat of seats. I was even missing the hardware bag and a short phone call it...
I seem to have a miss around idle -1800 rpm. I dont know if because of the cam or what. so today i pulled the plugs and #5 seems to be a lot darker than the others. Whats causing this? any advise please. thanks
sn95 porportioning valve question
I am sure that someone has installed one of these on a fox before. i have already installed everything from a 95 gt on my 93 gt except for the portioning valve and master cylinder. both are sitting in my garage. i plan on installing both but what is the...
just got a heck of a deal on a 97 mustang that is being parted out. i want to dothe 5 lug conversion with rear disk brakes. what problems will i run in too. thanks
henry
i am getting a air fuel ratio gauge this weekend. my question is that my tuners have been limiting the air f uel ratio to 12.5/1. by turning up my fuel pressure regulator from 42 psi up to around 48 can i get my air fuel down to around 12/1 or 11.5/1 at full throttle? i am hoping that this...
If you pull off the top of your intake and can see and rub the oil off the inside of the intake i belive that this is a little excess. maybe this is causing my spark knock. i have within the last 2 months replaced the pcv valve and little screen. today even put on a cheap ebay oil catch can...
If you pull off the top of your intake and can see and rub the oil off the inside of the intake i belive that this is a little excess. maybe this is causing my spark knock. i have within the last 2 months replaced the pcv valve and little screen. today even put on a cheap ebay oil catch can...
is it possible to put 347 pistons in a 331? imean they would both be for a .030 over bore. but would they fit and what wouold it do to the compession ratio??
Well my wandering idle is only after gassing it. I mean if i just punch the idle up toaround 1500 rpms. When it drops down it will go to around 500 rpms then back up to 1000rpms and then a couple of jumps till it settles around900 rpms. Do you have any suggestions ??. It actually stalled out...
hey has anyone put a 02-04 gt 80mm mass air on a fox body? i was havingtrouble with my mass air and he recommendedme to install a 02-04 gt.
just wondering if anyone else had done this.
I ve been reading and today tried to unplugg the mass air and run the car. To my suprise the car idled GREAT!! This was the first time since the new motor was installed in April. It idled @ about 850 rpm with the little rumble of the cam in it. I drove it to the gas stationed with it...
i have 2 tubes the one that was with the car when i bought it. It idled andran fine then with 24 lb injecter and then i bought a tube for 30 lb but there i now colors left on either one?? Does someone with a known 24 or 30 tube give me there measurement size on the flat end. Mine is 1/2" and...
If i take my car and punch while its in the drive way. When it starts to come down in rpms it will bounce up and down a few times maybe 2 or 3 times then jsut die. It even does this when driving. TPS is set a .97. any ideas??
Just put my 331 back in my car today and i am a little bit worried about the amount of oil in the intake. While the intake was off on the engine stand i could see oil pooled up on top of the valves. So i installed a new pcv and the wire screen. Well after going around teh block and stuff...