Search results

  1. 9

    Wtb Drivers Side Seat Slider

    I need a manual seat slider for a 95gt. ( drivers side only) Let me know if you have one for sale. Thanks
  2. 9

    performance distributer?

    I have a msd laying on my desk right now, less than 500 miles on it. The msd falls off like a rock after 5,000 rpms on the dyno. Changed plugs, wires, coil and tfi. Guess what, it was the $269 new distributor. Stay with oem. I bought a cheap china knock off, some parts of it were made in...
  3. 9

    Torq Thrust II's Trade or $450.00

    These wheels still available.?? Thanks
  4. 9

    Torq Thrust II's Trade or $450.00

    I take it these are 9 inch wide wheels??
  5. 9

    The slow build

    delete
  6. 9

    Which Permatex gasket maker for rear diff cover ?

    I've used it a couple of times on two different cars, everything ok to this point.
  7. 9

    1994 GT wheels

    Care to sell two rims. If you do, quote me a price. Thanks
  8. 9

    1994 GT wheels

    Questions: Still available.???? 2 rims or 4 rims for sale. 16" or 17" in size
  9. 9

    94 mustang parts car

    Looking for two 16" rims, in decent shape
  10. 9

    Coast High Performance?

    Three of us down here bought diy-- 347 blks, heads, pistons, flywheels etc from Ford strokers and Woody did a good job with us. Sometimes is a little hard to get a hold off, but will answer questions from some rednecks like us. Anyway I thought he did a good job for us. Don't know about...
  11. 9

    F/S Rocker arm studs

    For sale two sets of rocker arm studs taken out of two brand new sets of 1388 AFR heads, nothing has ever been on these studs. They are 3/8"s in size, two sets of 16 each. $25 per set. I used 7/16'th so these were removed. They are 1 7/8" from the bottom flat part of the stud that sits on...
  12. 9

    Water pump and timing chain questions

    Thanks for the replies.
  13. 9

    Water pump and timing chain questions

    1. What is a good high volume water pump to run on the 302 Mustang, using the orginal timing cover. This will be the reverse rotation, I guess. 2. How much slack should there be in a new double roller timing chain set. Mine appears looser than it should be. Probably over 1/4 inch slack...
  14. 9

    A few pictures of the 347 slow build

    Thanks, after we get the engine a little further along I hope to post a few more pictures.
  15. 9

    A few pictures of the 347 slow build

    The heads are 185 afr with a holly systemax upper and lower. Cam will be comp cam hr282xe . Have a 90mm-maf and a 75mm accufab race tb to go on. Rebuilt and reinstalled the rear end last weekend. New trac-pak and 3.73 gears and a new bearing kit. Will put new rotors on this coming weekend...
  16. 9

    A few pictures of the 347 slow build

    <table border="1"> <tr> <td></td> <td></td> </tr> <tr>Pictures of engine block/build and donor car sans engine. <td></td> <td></td> </tr> </table>
  17. 9

    Question on cam/ thrust bearing

    On my 347 build I'm finally to the point to put the timing set on. When I bought the engine it came with a cam retainer with hex bolts in the front. Now that I have broken the bearing behind the Summit performance timing set I'll ask the question. 1. Is the retainer suppose to be cut out to...
  18. 9

    lakewood 15202

    Not in yet, guess I found the answer, thanks for the reply however.
  19. 9

    lakewood 15202

    Will a lakewood 15202 bellhousing match up to a 95 GT with a tko-500. The adds keep stating it works on a 1979-93. If I have to change out the cable etc that's not a problem. Thanks.
  20. 9

    Header clearance question

    If the difference in the 87-93 long tube headers and the 94-95 headers is the location of the fork on the tranmisson, one is at 9 o'clock and one at 7 Then where does the fork come out from the tko-500 tranny. In other words does the tko-500 tranny allow you to use the 87-93 headers on a 94 or...