Search results

  1. F

    Hurst Billet Competition Plus Shifter

    I'm looking into a new shifter for my mustang and from what I can tell, the Hurst Billet Competition Plus Shifter has the most bang for its buck. Anyone have any opinions about this one or which one may be better. Keep in mind, Ford Racings shifter is more expensive and looks to be a hurst...
  2. F

    HOT ROD CAMS HELP!

    :flag: I've had my hot rod cams installed for about a year and a half now, and have consistently had the same problem of hanging rpms. It has come to my attention recently that it could be a vacuum line problem, i.e. there could be a knicked line in there somewhere that's causing the engine...
  3. F

    SALEEN SUSPENSION KIT & CAMBER BOLTS

    I recently installed the saleen suspension kit on my car, then I had Les Schwab align the car. Once they brought it back close to factory specs there was a noticeable negative camber on the front wheels. They tell me I need camber plates, which they say cost 345 for the set, but I talked to...
  4. F

    Lowering Spring install question

    I've got a Saleen suspension kit I'm about to install in my mustang..the kit has the front sway bar, rear springs and front strut assemblies....my question is this: when I do the front spring installs, do I really need to install camber/castor bolts in place of the stock bolts? Also, the kit I...
  5. F

    How many Motor Mounts do I need?

    Can someone please let me know how many motor mounts I'll need for my mustang? My hot rods cams really make the engine shake, audibly and noticeably so. I was thinking that motor mounts would at least dampen this effect. Will one set of Steedas motor mounts work? or do I need more? thanks.
  6. F

    how many tunes does it take to make your car run rite after cam install

    I'm currently having the same problem with my hot rod cams from Ford...i had the car dyno tuned and the rpms are now sticking at seemingly random times...i've been working with my tuner and getting tunes emailed to me...the problem was that the car didn't have problems during the dyno tune, only...
  7. F

    Hot Rod Cams frustrations: Can Anybody Help?!

    good ideas thanks...i hadn't yet tried calling the installer as i had assumed it was the tune itself...i'll speak with the installer tomorrow...thanks!
  8. F

    Hot Rod Cams frustrations: Can Anybody Help?!

    Not too recently now I bought and installed a set of the modular 3v hot rod cams from Ford Racing. I had Ford do the install and a tuner do the dyno (using SCT software)...since the install and tuning, I've been getting what can only be described as "hanging rpms"...immediately when I drove...
  9. F

    S197 WHEEL SPECS

    Anyone know what the load rating is on the stock 18'' wheels? I'm looking for new wheels but I want ones with equal or greater load ratings so I don't get that annoying vibration like with cheaper wheels. thanks..:hail2:
  10. F

    Dealer incentives..is it worth it?

    With the economy the way it is, and with dealer incentives piling up..has anyone given any thought to trading in their mustangs for new mustangs like the GT500 or the Roush mustang....if you've been on a dealer's lot in California anytime recently you've probably seen roushes going for less than...
  11. F

    rear end gear ?

    Look at the axle cover in the middle of the rear axle...that will tell you what you're working with...also, and i'm unsure about this, but you might be able to check the door jam sticker for that info... that being said, it's likely a 3.23 gear ratio (maybe even a 3.53)...however if you're...
  12. F

    Motorcraft vs Aftermarket fuel filter

    I'm changing out my fuel filter and was wondering if anyone has any suggestions as to which one I should choose? I recently installed my FRPP Hot Rod Cams and I want to get the most out of em. Thanks:hail2::SNSign:
  13. F

    FRPP Hot Rod Cams Question

    I guess I had it in my mind that I needed to do a phaser mod with these cams...I'll just have to keep it away from WOT until next week when I can get time on the dyno....thanks
  14. F

    FRPP Hot Rod Cams Question

    I'm having Ford install my hot rod cams on monday...does anyone know if these cams can work properly without additional tuning? All I need is to drive the car for a week until I can get some dyno tuning done at the local shop...anyone have any experience? thanks:nice:
  15. F

    CompCams Question

    My FRPP hot rod cams arrive on monday...once I get them installed, what's the break-in period like? thanks for the help!
  16. F

    CompCams Question

    alright thanks guys I appreciate the help...I guess my main concern was the spring upgrade, which after long debate with myself I've decided to get away from the spring req'd setup..that being said, if I'm not going for the springs or phaser upgrades, why not get a FRPP part instead..all the...
  17. F

    CompCams Question

    my problem is that people have consistently told me to get either one or the other...when they tell me to do the spring upgrade they say its a superb upgrade with great sound and power gains...when they tell me to get the NSR they never say why...someone help!:hail2::SNSign: p.s. i'm a five speed
  18. F

    CompCams Question

    I'm trying to get my new cam choice pinned down...many people say just to go with the CompCams StageII NSR (no springs required)...but all the research I do keeps leading me back to the StageII VSR (valve springs required)....I'm wondering if anyone's had any experience with either of these...
  19. F

    Do 4.10s make 1st gear useless?

    only do the install if you know what you're doing...get the kit with the new bearing if you do it yourself...just remember, there are quite a few things that can go wrong if you don't do the install right (i.e. 50-50 chance you're gonna break something upon pulling the differential apart)...if...
  20. F

    Alert the presses! 200 HP+ and 75+ MPG!

    Great for a laugh, yet also very sad...you'd have to be a fool to fall for this!! Thanks for the post...lol :ban:
Top Bottom
Back
Forums
Menu