Search results

  1. 1995GTStang

    T45 throwout bearing issues

    The t45 is stock to car 1997' Thank you
  2. 1995GTStang

    T45 throwout bearing issues

    I have a 97' GT. My throw-out bearing damn near seized up on me. It looks like it scored the bearing shaft from the front of the transmission. How difficult is it to replace these and where do you find them? Thanks
  3. 1995GTStang

    Need some help......What could it be, vacuum leak or timing off a tooth

    check your spark plug wires as well. Make sure you dont have them crossed wrong or on the wrong plug.
  4. 1995GTStang

    1996 GT Automatic trans issues

    fuel pressure is pretty steady.....could it be the TPS?
  5. 1995GTStang

    How do I take the front bumper off

    You have two bolts on that attach the bumper on each side that attach to the fender. The only way to get those is around the wheel well. You will prob have to remove a couple of those plastic tabs that hold the wheel well on to get your hand in there with a ratchet. I believe they are 10mm...
  6. 1995GTStang

    1996 GT Automatic trans issues

    I was just helping a friend of mine who has a stock 96 GT automatic. The car runs good but when he attempts to hard accelerate the car studders and spudders and bangs...but does not take off. The car will drive just fine, but its only impacted at full throttle. Any suggestions??
  7. 1995GTStang

    Having problems finding right speedo gear

    I just swapped to 3.73 from 2.73 gears. The place that did the work put a black 20t speedo gear into the T45 transmission. At 60mph my speedo was saying I was doing 71-73mph. I swapped out the 20t for a red 21t speedo gear and now at 60mph its says I am doing closer to 65mph. Has any one...
  8. 1995GTStang

    2.73 to 3.73 gear swap

    Wow....major difference..... I just got the car back from the shop yesterday. I had to have the whole differential rebuilt. But completely worth it....it is like having a new car. I highly recommended a PI and gear swap on these....definitely awakens these cars!!!
  9. 1995GTStang

    97 gt engine swap

    I just put a 2002 4.6 PI engine into my 1997 GT. It is actually a good and fast swap. You can drive it around just fine without even having a tune. The PI engine is a vast improvement over the NPI engine. But do not expect a 13 sec car until you have it tuned.
  10. 1995GTStang

    Help my car will not rev over 3500 rpms

    I agree with WMBURNS if anyone in the future starts having similar problems, I would recommend starting with a new fuel filter....approx 12-15.00 and it only takes about 10mins to swap out. If that does not eliminate the problem, work your way forward. With the car running see if you hear any...
  11. 1995GTStang

    2.73 to 3.73 gear swap

    Hills Automotive on Division They are doing a differential gear swap and bearing replacement for about 1100.00. That is about 200.00 cheaper than any other estimate.
  12. 1995GTStang

    2.73 to 3.73 gear swap

    Yeah, pretty close....we live in Davenport, about 35 miles west of Spokane. Where are you?
  13. 1995GTStang

    2.73 to 3.73 gear swap

    When is the opening day usually for Spokane raceway?
  14. 1995GTStang

    2.73 to 3.73 gear swap

    I appreciate the info..... I wish I could take it to the track. We have over 12" of standing snow on the ground and the local track is closed for season. I found a good reputable shop offering a great deal on a gear swap. Since I do drive this on the highway quite a bit I pretty much knew...
  15. 1995GTStang

    2.73 to 3.73 gear swap

    I am having my gears swapped in my 97' GT 5 speed. I recently did a 4.6 PI engine swap and with a 70mm BBK throttlebody and CAI setup. It has a highflow catted x pipe and flowmaster mufflers. What approx should I be running in the 1/4 after gears? and then after a decent tune? Thanks
  16. 1995GTStang

    Need some help......What could it be, vacuum leak or timing off a tooth

    Your absolutely right. I do have a picture of the crank gear....not the best, but it shows that the hole is at the 6 o clock position. I did all the work to the motor when it was sitting on pallet. http://i59.photobucket.com/albums/g287/Camarofanatic75/new050.jpg I will go hit up Napa for...
  17. 1995GTStang

    Need some help......What could it be, vacuum leak or timing off a tooth

    Well I am pretty sure I know what was causing the code PO300....I left the cam sensor unplugged....and I forgot to attach it before running other tests. I plugged it back in and cleared it....so far no more codes. However that did not fix the initial problem. A local mechanic swung in and...
  18. 1995GTStang

    Need some help......What could it be, vacuum leak or timing off a tooth

    Great information...its a start...I will pull all spark plug wires check them and rerun them to their locations. These have the cylinder marked on them as well as the coil packs. I double checked and they are going to the right locations. Could this be the reason why I am having this type of...
  19. 1995GTStang

    Need some help......What could it be, vacuum leak or timing off a tooth

    Ok, I went out today and started it up drove it around the block. It gave me the code PO300 cylinder misfire (x2) two counts of the code. My scanner did not give me the TPS open/closed loop information it just said 19.6 I am assuming that is voltage. here is a link to car...
  20. 1995GTStang

    Need some help......What could it be, vacuum leak or timing off a tooth

    I really appreciate the information given...it gives me a few steps to try tomorrow Cats are good....car was running 14.9 in complete stock form before I started the swap. I will also take a short vid of the car running to give you an idea of whats going on. I believe I have a photo of the...
Top Bottom
Back
Forums
Menu