Search results

  1. UPRMike

    has any one tried upr intake tube

    All you need is a 3 1/2" to 4" coupler. Our kit comes with two 3 1/2" straight couplers and all we have to do is substitute one of them. If you decide to order make sure to specify that so we can alter the kit for you. Also, PM sent -Mike
  2. UPRMike

    Help me help a customer. What MAF CAI is this?

    Ok so the housing is Steeda and the electronics are stock. Gotcha. Thanks a lot for the fast response. It was a big help! :nice:
  3. UPRMike

    Help me help a customer. What MAF CAI is this?

    Hey guys, got a few photos from a customer today and we're trying to get a program for him to ship out a tuner. Problem is, he had no idea what kind of MAF sensor and CAI kit he has becasue they were on the car when he got it. Any help would be greatly appreciated. (I'm guessing C&L on the...
  4. UPRMike

    99 Cobra brakes help

    That is a handy tool, actually. I've also done it by laying a flat screwdriver sideways in the large groove cut in the piston and turning it about a 1/4-turn at a time to back it back in. The tool is better, though.
  5. UPRMike

    99 Cobra brakes help

    Nothing you wouldn't need on a Fox. It will all be familiar, just bigger. It's actually easier because you don't have to to handpack bearing and make a mess if you need to change or turn the rotors.
  6. UPRMike

    351W question

    Do you mean can it be changed with the engine still in the vehicle? If that's what you're asking, yes, and it's no more difficult than a one piece. Cars had two-piece rear mains for a few decades and they were changed out regularly, often as preventative maintenance during a clutch job.
  7. UPRMike

    alternative to hood pins?

    You might like these. Still a pin but a drastically different look: 64-10 Mustang Billet Hood Pin Kit Black -Mike
  8. UPRMike

    Low Oil sensor..did do a search

    No problem :nice:
  9. UPRMike

    Low Oil sensor..did do a search

    You'll be fine if you don't want to add the bung. The low oil light only turns on if the sensor is plugged in, so just tie the wire up out of the way and maybe tape off the end so nastiness doesn't get in the connector. I've got a '90 with a Moroso 7-quart. No bung, no sensor, no light.
  10. UPRMike

    don't know what k-member to buy!

    Yep, our kmember and arms keep everything in the stock location as far as wheelbase (no forward offset) goes, but we also have arms that are 1" shorter than stock (and stock length, of course) to tuck the front wheels under the fenders if you like.
  11. UPRMike

    don't know what k-member to buy!

    Ride height is probably the biggest selling point of a coilover setup: it's whatever you like. The spring seat on a coilover setup is fully adjustable, so after you pick the spring rate for your application you can set the stance of the vehicle as you see fit. This is a great advantage over a...
  12. UPRMike

    broken crankpulley need help

    I bet a dollar to a doughnut that when you took the bolt out, the heavy duty washer that goes with that bolt stayed behind in the center of the damper. That would cause what you've done here: you're not actually pushing the crank snout and pulling the damper assembly to get it off, you're...
  13. UPRMike

    1993 Cobra RR's...worth it on stock heads/cam?

    I agree with v8only, it's not a bad job at all to swap out rockers. They don't have to be adjusted, and it'll get you familiar with the procedure for setting up the valvetrain. Easiest way to remember the sequence when tightening down the rockers is to think ICE. In other words, As you crank...
  14. UPRMike

    Guys please check my order list before I place it.

    For the alternator, the easiest way to set it up for the increased amperage load is with this kit: Power Wire Kit, 4 Gauge, 3G, Premium W/Noise Suppression at LRS - Same Day Shipping! The part you may be overlooking is that the stock timing cover on your 5.0 won't be compatible with that...
  15. UPRMike

    8.8 rear diff question

    Is there one at either end of the housing? Quad-shocks and brackets maybe?
  16. UPRMike

    8.8 rear diff question

    Year and model of the rear end would help us too, if you know it.
  17. UPRMike

    don't know what k-member to buy!

    Yep, I'm the Intarweb Liason :). For the best all around performance, I'd suggest the Qa1 front struts that are fully adjustable and designed to be utilized in a coilover setup from the start since they built with a threaded aluminum body. They adjust on the car and have a very broad range of...
  18. UPRMike

    don't know what k-member to buy!

    All of our K-members are American made from chrome-moly tubing sourced form the same supplier that provides a lot of the Top-Fuel teams with stock for their cages. Since we're a supplier for both our own and Qa1's k-member we can provide you with decent comparison info as well as provide any...
  19. UPRMike

    vaccum line question

    Yep, they can get a little funky after a couple decades. It's not too expensive to replace: 79-95 Charcoal Canister, 5.0L at LRS - Same Day Shipping!
  20. UPRMike

    Heater Core bypass

    ^^^ THAT is the best solution I've ever seen to bypassing the heater. I really wish I'd thought of it. Yes, definitely do that :nice:.
Top Bottom
Back
Forums
Menu