Search results

  1. L

    Help me with the codes I got...

    I just got back in from getting the prochamber correctly installed and I re-checked codes and most went away like I figured they would once I had the prochamber installed, but I gained 2 more. Codes are: 31 (still) EGR/SMOG Simulator I purchased will solve this one so I'm not worried. 81 85 If...
  2. L

    Help me with the codes I got...

    I just completed a HCI swap on my 91 GT and I got a few codes. Below are what they are. Thanks again every one. Judd 31: PFE, EVP or EVR circuit below minimum voltage 41: HEGO sensor circuit indicates system lean No HEGO switching detected 87: Fuel pump primary circuit...
  3. L

    Where should I set my FP and timing at?

    Where do you suggest going? I won't go to SGS since I feel I got ripped and the head shop they used rip me has well.
  4. L

    Where should I set my FP and timing at?

    No plans to do it, just saying. Most likely I will go with a SC and have to bump up to 40#'s in a yr or two any how. Depends where I'm at. My job like every one else's is not guaranteed. Obami cut to much Military funding and I have one pay left till I got to go out in the civi World. :) Any...
  5. L

    Where should I set my FP and timing at?

    I know a lot of ppl think 30# injectors are over kill, but there is a lot of people running them with no issues. I just figured it's better to have bigger injectors that are not running close to the max independence. Plus it helps if I had nitrous later on or what have you.
  6. L

    Where should I set my FP and timing at?

    unless any one chimes in I will start out with the numbers your provided. Thanks for the response.
  7. L

    Where should I set my FP and timing at?

    Pretty much done with my HCI swap and ready to start her up tomorrow. Just have to install the Radiator, Electric fan and the Electrical fuel gauge. Just wondering where I should set my Fuel Pressure and timing at? If it helps the Engine mods are below: AFR 165 heads with 1.6 7/16 stud mount...
  8. L

    Small case 3g wiring question.

    I want to know if I did my install correctly. I purchased a small case 3g wiring kit (complete with 4ga wiring and fuse block, connectors and plug) about a year ago and lost the instructions. I searched, but a lot of sites I seen weren't to clear so I figured I'd post. Below you can see a quick...
  9. L

    Need help figuring out if I threw away brackets and bolts

    Thanks for the reply 87GT. I got the long PS bolt I Was missing so I'm good on that side. I still need the Alt side tho. Just basically looking for pictures of how it's mounted. Not sure if you have one of those kits installed like March Performance where there's a tension rod, but if you do...
  10. L

    Need help installing MAC Prochambers to my MAC LT's

    well if it comes down to running opening headers then I must :)
  11. L

    Need help installing MAC Prochambers to my MAC LT's

    I'm currently trying to install my MAC prochamber's to my MAC LT Headers and have a issue. Seems one side is about 8" or so off. If I slip the left pipe on the left (drivers side) header then try to put the only side on there's a gap and same vise versa. Any easier way to do this? Kinda sucks I...
  12. L

    Need help figuring out if I threw away brackets and bolts

    bump. Can any one please help me out> ? I'd do it for you guys/gal Thanks /judd
  13. L

    NEED ARP TQ SPECS for HEADERS PLEASEEEEEEE

    mustank I know it's tight in there but I had a custom socket my dad made since he is a old school racer that would have worked. Just wanted to make sure I did things right if it did in fact require proper tqing. I know most ppl don't even tq there plugs and has silly has it is I might be one of...
  14. L

    NEED ARP TQ SPECS for HEADERS PLEASEEEEEEE

    thanks drew, did just that. Just wasn;t sure like I said since I was dealing with alum heads and I heard ARP has there own tq specs. Sorry for the bump shortly after, I am just ready to fire this up and hear that cam lobe :) Just need to find the Alt bolt since I gave it away with my stock...
  15. L

    NEED ARP TQ SPECS for HEADERS PLEASEEEEEEE

    thanks for the response Drew. Heard that to, but also heard ARP has there own tq specs especially with AFR ALUMINUM heads
  16. L

    NEED ARP TQ SPECS for HEADERS PLEASEEEEEEE

    I have the ARP 400-1202 3.8" x .750 SS 12 pt header bolt kit and I have the bolts snugged up. I am looking for the tq specs so I can tq them down. I was told ARP has there own specs and not to go off of what I was tq the stocker equipment to. Trying to tq down LT MAC HEADERS to AFR 165cc...
  17. L

    Need help figuring out if I threw away brackets and bolts

    I'm wanting to install my Alt and PS today but think I might have thrown away a few parts - not on purpose. I know there is a long bolt that goes into the drivers side head which the PS mounts to that I could not get off the stock head so I let it go to the guy who bought them. Just not sure if...
  18. L

    Wrapping up HCI wanting to go to the track q's

    well sine I have a few 5 gal jugs of Mobil1 that I use for my cheap oil I will just go ahead and after letting it warm up drain and re-fill with that. Thanks for the reply.
  19. L

    Wrapping up HCI wanting to go to the track q's

    Once I install the radiator, hoses and a few misc wiring I'm hoping for this HCI beast to fire over. If and when that happens my plan was to let it idle till it gets up to normal operating temp adjusting fuel via gauge and timing has needed to keep it going. Once it warms up I plan on draining...
  20. L

    Looking for new Manifold to TB Bolts

    What was the size you got b/c I need it (obviously) to tighten into the manifold and then the 75mm EGR spacer and TB have to go on
Top Bottom
Back
Forums
Menu