Search results

  1. M

    For Sale 1974 Mustang Ii Project $500 Near Chicago

    The engine is a 1986 roller with Edelbrock performer cam. Edelbrock RPM air gap intake. Headman headers. Holley 600 cfm 4 barrel carb. The engine was completely rebuilt by the former owner. Ran strong before I took it out.
  2. M

    For Sale 1974 Mustang Ii Project $500 Near Chicago

    Up for sale is a 1974 Mustang II Ghia that is setup for a 302. I originally bought this car for the engine alone in 2005 but fell in love with it so I drove it for a couple years. Tore engine out later to refresh and do other modifications but ran out of time or interest before getting it...
  3. M

    Need some hepl guys, fan belt

    Well mines not stock, but the pulleys themselves are. The water pump pulley should inset into the water pump. The belt then goes in the middle groove of your crank pulley and to your alternator. Alot of times the spacer for the alternator got missplaced and rigged up, so make sure the alternator...
  4. M

    How about longer wheel studs

    Just took a leap of faith with arp wheel studs. I compared dimensions on their MII front wheel studs and the knurl would've been way too big. I ended up using the 2005-up front wheel studs. The knurl was three thou smaller, just barely needing cleanup with a round file. A couple thousandths off...
  5. M

    anybody still use this?

    whats the crossmember look like? Mine needs taller humps than stock
  6. M

    transmission crossmember troubles

    Heres a brain buster. I have the crappy headman headers installed in my ii (after much persuading with a sledge and a torch). Now the passenger side header outlet sits above the the transmission crossmember about an inch. Im sure the beating on the headers didnt help matters any. I have a...
  7. M

    How about longer wheel studs

    Any idea where to get some longer wheel studs for the rear of the mustang ii? Dormans website is stupid, they give about ten different ones, all of which had different knurl sizes than mine. Also my wheel stud knurl measures about .542 is that correct?
  8. M

    Leaf Spring Shackles

    Well i bought new shackles for my rear end. All the websites i was on had shackles that had a larger bushing on bottom and a smaller on top. I assumed these would fit and bought them. Well, i cut my old ones off and found the top bushing on mine is large, just like older mustangs. Will the old...
  9. M

    Rear end Question

    Im putting in a richmond rite lock in my 8" and the side gears look really worn and need to be replaced. In my manual it only shows 4236 for the part numbers, but i looked online and there are a lot of side gears that include 4236, but there are four other numbers in front of them, all...
  10. M

    8" rear end bearings

    thanks ill keep at it. i think i found a place to press in the bearings. hopefully it wont be one of those two month projects.
  11. M

    8" rear end bearings

    Well i got new springs for my II and while i got the rear end out i figured ill replace the bearings and seals. Well i took out the axle just fine, but the retaining ring on the bearings are giving me some trouble. The shop manual says to hit it with a cold chisel in several spots and it should...
  12. M

    Head Ache

    I thought you only put anti-seize on bolts that are going into aluminum. Am i correct anyone? I also remember putting it on exhaust collector bolts.
  13. M

    yellow wire.

    thanks for the reply, hopefully it'll be running soon!
  14. M

    yellow wire.

    Alright, i'm putting in my wiring for my battery to relocate it to the trunk. Ive got the starter relay in the trunk as well. Ive hooked up the battery wires to each side and the red/blue ign wire to the i terminal. Is this all that goes on the relay? Or does a yellow wire go there too? I think...
  15. M

    alternator wiring problem

    Alright so im ready to put in my alternator, but forgot which wires go where. can anyone post a picture of the back of the alternator so i can see?
  16. M

    alternator bracket

    i made my own bracket out of the regular bracket. its functional, but the chrome is shot now.
  17. M

    Trans cooler line problems

    thanks for the reply, i think ill just go with those oem ones, then at least ill get a general idea to adapt those
  18. M

    alternator bracket

    for some reason the alternator bracket on my 302 doesn't seem to be lining up right. i looked at pics from the internet but they are only of water pumps that outlet from the passenger side, and there is an extra bolt hole that mine does not have. is there a special bracket i need for it? Also...
  19. M

    Heater parts.

    Ive got most of the heater parts out of my II. Free to anyone who wants it. Includes blower motor, plastic plenum, cables, etc. I live in Joliet, about forty minutes south west of Chicago. The only parts im keeping are the vents, it wold look stupid without those. A few of the plastic pieces are...
  20. M

    Trans cooler line problems

    I'm starting to put back together my II and ran into a problem. I cant remember how my trans lines are run. Its a c-4, pan fill, that looks like someone brazed a fitting on to the pan right next to the dipstick. i think this brings the fluid to the cooler and the fitting on the side of the trans...
Top Bottom
Back
Forums
Menu