Search results

  1. bigsexxy422

    ambeant air temp location

    I am working on a mustang for my boss and the car is running very rich. I connected my scan tool to it and it says that the ambeant air temp is -7 degrees. I cant seem to find the sensor tbough. Where is it located?
  2. bigsexxy422

    head bolts

    i am installing the heads on my engine tonight and i was wondering. i am replaceding the old cast heads with new alum. heads. do i need washers on my head bolts to keep from digging in, or should it be ok with out the washers? the cast heads didnt have any washers on the bolts.
  3. bigsexxy422

    timeing chain strech

    i am assymbling my engine and i am wondering if i should use my old timeing chain or not. it is a double roller, and when i removed it the chain seemed to be streched, i am wondering how much they are expected to streach, and if i should use it or order a new one. this one only has maybe 7k...
  4. bigsexxy422

    wanted to buy 347 crank

    i am looking for a 347 crank and rods
  5. bigsexxy422

    balancer weight

    i am wondering what the ballancer weight should be for a 1980 engine and crank, is it 28oz or 50oz?
  6. bigsexxy422

    head gasket question

    i am getting ready to reassymble my engine and i need to get head gaskets. the block has been bored .030, and i am wondering if i should get the head gaskets that are made for that or if a stock bore gasket will work. i only ask because i can get a compleat engine rebuild set with head gaskets...
  7. bigsexxy422

    whats the biggest cam in a stock 302

    i am trying to pull the trigger on a cam selection and i am wondering what the biggest cam is you can run on a stock 302 lower end. the car is carbed so i dont have to worry about messing around with a computer, and lets just say it is with the stock heads out of an 89 gt.
  8. bigsexxy422

    engine, ecu, maf, wire harness

    i have a complet stock 5.0 ho out of my 1989 gt, 5 speed i also have the stock ecu, maf, and wire harness. make me an offer
  9. bigsexxy422

    so what do you have?

    ok i have a post about what would be a good cam for my engine setup, but since it is too hard to get peoples opinions on what would work i figured i would see what tey got. what cam are you guys running in your enigne. i know efi and carb are different, along with other factors, so i will just...
  10. bigsexxy422

    driveline vibration

    so i have a vibration in the car when going around 65 mph. i just recently did a rear gear swap from 2.73 to 3.55. i figured it was the driveshaft out of balance since i only had a small vibration at around 100 with the old gears and its around 65 with the new ones. what do you guys think? and...
  11. bigsexxy422

    lifter question

    ok guys here is my question. i have a colapsed lifter in my 5.0 and the cam and lifters are only about 4000 miles old. i know they should not go this fast but the guy who buillt my engine is a bit of a scam artest. so anyway my question is that if it is ok to install 16 new lifters on the cam...
  12. bigsexxy422

    roller rocker question

    ok i am looking to change the rockers on my car to roller rockers. i have a cam in it with 484 lift with 1.6 rollers, and i was wondering if i could fit 1.72s with that cam. the bottom end is stock except for being bored .30 over, and new pistons. i have the stock heads. thanks for the help
  13. bigsexxy422

    ENGINE, COMPUTER, WIRE HARNESS, MAF

    i have a compleat engine out of my 1989 gt. it has arount 124 thousand on it. i pulled it to install and engien i had built. it ran great when i removed it. i also have the ecm, wire harness, and maf sensor. i am willing to sepperat if nobody want the whole package. make me an offer or will...
  14. bigsexxy422

    RIM PROBLEMS

    i have an 89 gt with cobra rims on it. i noticed that when i cut the wheel all the way to the left or right that the inside lip of the rim is hitting the control arm. is there some kind of stop i could weld on the control arm to stop the knuckel from turning so far, or maybe do i need different...
  15. bigsexxy422

    distributor help

    i have just recently got a new MSD distributor for my 5.0 i was wondering what springs i should run in it. i know i should have the base timeing around 14, but im not shure what springs to run. it is borde .30 over, has a single plane high rise intake with a 600cfm edelbrock on top. it has a 454...
  16. bigsexxy422

    ROCKER ARM HELP

    i just had and engine built and broke it in the other day. i had a small tick comeing from the valves. i adjusted the play in them and noticed that on the rocker arm itself it says 1.5. i looked on my cam card and it says i have 484 lift with 1.6 rockers. i am wondering if my engine builder is...
  17. bigsexxy422

    stock h pipe

    i am selling the stock h pipe out of a 1989 gt. it is a 4 cat h pipe and in great condition. 100. obo
  18. bigsexxy422

    stock 302 HO out of a 89 mustang for sale

    i am selling a bone stock 302 out for my 89 mustang gt it is a 5.0 HO, it ran great when i pulled it out. will sell other parts with it if needed. also includes the computer and wireing. make me an offer local pick up only i am located in fosterdale N.Y.
  19. bigsexxy422

    pully question

    i am swapping out a used and abused 5.0 for a freshly rebuilt one. i got a new dampner for the new engine and when i pulled the crank pully off the old engine and tested it on the new one the water pump pully and crank pully didnt line up. i see on the old dampner that there is about a 1/2 inch...
  20. bigsexxy422

    new front clip

    i just started ripping my stang apart for some front end rust. i need a new front clip for a 1989 gt. dont really care about the color i have to paint it anyway. new would be great but i dont wanna pay that much. thanks for the help