Search results

Hello fellas I want my stock rpm in my cluster to work again. I did a carb swap and would like my bbk cluster to work like it was. I have gone and spliced into the green and yellow wire behind my cluster #11 and ran it to my negative side in the coil and on my msd box tach signal hook up and...

l

?#1 WHAT INTAKE SHOULD I USE??..I HAVE PROCOMP DUAL PLAIN LOWER INTAKE AND A IMITATION LOWER INTAKE VICTOR JR. ?#2 WHICH ROCKERS SHOULD I USE.. 1.6 OR 1.7 ITS MY DRAG CAR SO LOOKING FOR THE BEST SETUP ON THE TRACK! RUNNING A E303 COMP CAMP WITH 373 GEARS WITH 5 SPEED TRANNY..CARBED MOTOR...

OK FELLAWS IM RUN NITROUS ON MY CARB SETUP. HERES THE CATCH THOE IT WAS ORIGINALY EFI SWAP TO A CARB RUNNING A REGULATOR ON A STOCK INTANK FUEL PUMP. I KNOW THATS THE GUETTO WAY TO GO FUEL WISE BUT WERE DO I GET MY FUEL FOR MY WET KIT

Ok guys just a quick question here me and my buddy both have 88 mustang 5.0. His is fuel injected mine is car we both have e303 cams he has a lopy idle realy nice mine is quit it only sounds lopy when its cold when it warms up u cant even tell i have one my cam is advanced 4 degrees and i have...

what about a mild car like mine with the setup i have do u think 6000k is oky

Ok fellas i wondering how high i can rev my setup. My setup consists of procomp dual plane intake (1500-6500) holley 600 carb e303 cam longtubes (fullexhaust) alumenum pullies 373 gears alumenu d-shaft gt40p heads (afr springs) 1.7 rockers msd 6al2 msd wires and about 30 Degres of timing

anyone

I just bought a 6al2 ignition box for my carb 302 mustang.Im having installation isues i have the intructions but dont quite get them i have follow the diagram but its not working.Heres what i got done heavy red is connected to positive on the starter solenoid heavy black to negative on starter...

I will work on the spelling thx. But i have folow ur steps and nothing i dosent seem to have vacuem leaks as i have check for that.

ok guys i just purchased a simi build 306 mustang gt the mods are fully build botom end stock heads ported x cam 1.7 rockers edelbrok uper and lower bbk spacer and trottle body cnl 76mm cal for 24 injectors the isue is this think pops like cracy out of the cold air intake timing is set at 10...

It only does it when it gets rev up or when i get on it. This moter i have on know does not have more then 5000 miles on i dont get why it would be doint that all bearings piston rings got replace what do u mean by w/ the TB block wide open.

Okay guys like the titlle says i did a compresion test on the car beacause i found oil or gas on the treads the results were. cylinder1 60 cylinder2 60 cylinder3 70 cylinder4 70 cylinder5 60 cylinder6 70 cylinder7 70 cylinder8 75 now the car runs great no overheating oil presure looks good...

Yeah still there guys.So let me ket this straight the new kit i whant to get would work on my car mount the fuel pump somewere under the bumper were it shows "i kind think that makes the car look beefy from the back"run a line from the pump to the reg somere in the engine bay from the other...

I dont think i ever had one going up to the engine comparment. But i quess it dosent hurt to check.

Thank you for the heads up i will try to right this stuff beter.But back to the topic how would i go about making a vent so the vapors can get out

Okay guys i fix the isue with my carb got it to idle just were i whant to and i think i set the idle screws just right. when i did my carb conversion i kept the stock efi fuel pump and just ran a carb fuel regulator.Well know the reg is not being very accurate it reads like 9 psi one day the...

mostly a drag car but every once in a while take it out on the street

whictch one would u recomend and is the choke for cold starts orcan u tell me what that is sorry new to the carb wrold

ok guys ones again asking the pros Im looking to buy a new carb since my is not working right. i have my mind set on a 600 holley double pumper. im not very familiar with carb setups as i just recently swap from efi to carb my question is i have a 302 Dual Plane Aluminum Intake that makes its...