Search results

  1. mustang_matt

    BBK LT headers trans removal

    I agree with rd just pull the motor and tranny all at once. I have long tubes also and there is no way i would fight them to do a clutch job
  2. mustang_matt

    L/Ts + an existing Bassani X Ques?

    b4 you buy go to your local exhaust shop and have them look at it. sometimes you can cut the x pipe down and flair the ends to except the l.t.s I've been down this road b4 on 94 5.0s and it worked, not sure bout the 4.6s with you set up. cant hurt to check and it will be cheaper than buying a...
  3. mustang_matt

    03 mustang gt tach signal?

    I think you can use pin number 46 for a tach signal.
  4. mustang_matt

    2004 Mustang GT looking 4 1st upgrades

    4.10s, a shifter (steeda or 5.0), subframes, and a BBK 78mm t-body inlet. damn good starting point.
  5. mustang_matt

    Dorman Intake Manifold

    the dorman is ok. but just ok. the intake runners are MUCH smaller than than the ford p.i. intakes. Just do the ford intake.
  6. mustang_matt

    97 gt engine swap

    Just remembered I do have a sct boxed tune... but I did run it with a stock tune :rolleyes:
  7. mustang_matt

    Modification Survey Thread

    WOW this has been going on for awhile! Well Heres my 2 cents 1997 Mustang GT Has a 2001 Lincoln Town car P.I. motor swap K&N c.a.i Small SOTP feel more engine noise BBK 78mm throttle inlet (Highly recommended!!) car pulls so hard from 4500 up 1/4 " Dallas mustang plenum spacer. had to drill...
  8. mustang_matt

    97 gt engine swap

    My Stangs stock 1997 computer tune is what I'm running with my P.I. swap with a host of mods and it runs great. Fix'n to go turbo on my car then I will get a tune. eewwahaha< evil laugh:D
  9. mustang_matt

    Tri-ax vs. Pro 5.0 vs. MGW on a T5

    I have run both the Tri ax and the pro 5.0. BOTH are great pieces of hardware. The only complaints I've had about the Tri ax is the weak feeling handle, but you can get a replacement for it that is stronger, it also has pretty smooth engagement and positive stops. The Pro 5.0 is my preference...
  10. mustang_matt

    my new baby UPDATED

    good looking car! and Lars you are so right texas blows cause of that law.. front plates just take away from the car.
  11. mustang_matt

    Stupid windows don't roll down

    hey what year is your car? I have a 97 and had a 95 that both had a similar problem. Inside the door panel near the upper left hand side is a black box. On one of my cars it came unplugged on the other it went bad. I forget what its called but it has number on it, you can by pass it with a...
  12. mustang_matt

    swap issues??

    also if you dont like the flowmasters (I have these, I know how much they can drone on the inside of your car) try borla pro xs they sound incredible!! I put a set on my buddies 94 GT. You know the mustang in the first Transformers movie? Thats wat his car sounds like.. Also 5.0 mustang magazine...
  13. mustang_matt

    swap issues??

    2wheelryder if your gonna do a plenum just get the 78mm BBK plenum intake.. I bought one about 3 months ago, GREAT mod the car pulls so hard from 4500 to 6000. It costs a little more than the macs or professional products or C&L plenums, but its well worth it. I'm running it with a 1/4 inch...
  14. mustang_matt

    Where to start to gain hp?

    Well my approach is not as glamorous as some of the others but it will grow with you AND the car will be faster.. start at the rear and come forward. 4:10 gears, diffie cover, hardened axles, suspension, long tube exhaust, programmer, tubular k-member, after you do all the chassis and suspension...
  15. mustang_matt

    Suggestions on rear end gears..

    Are you forced induction? if you have a turbo set up I'd go with 3:27 or 3:55s if you have a roots type blower go 3:55s, if you have a centrifugal supercharger go 3:73s, if your N/A go 3:73s
  16. mustang_matt

    Suggest some loud mufflers!

    or spin tech if your state requires mufflers
  17. mustang_matt

    Suggest some loud mufflers!

    off road H and straight pipes. my friend has this set up on his 04 cobra. its retarded loud. sounds like a farm truck :) but it is loud..
  18. mustang_matt

    swap issues??

    I just did this swap. you'll need a new intake, one with a coolant fitting. I used a 2001 lincoln town car motor. then I bought professional products intake and had it drilled. You can also use a DORMAN intake for a p.i. engine from any autoparts store or buy a ford racing replacement you'll...
  19. mustang_matt

    dual plug heads to a 81 turbo

    dont bother with the dual plug head. I built a turbo 89 stang a few years ago, and the dual power heads just doesn't flow as good as the turbo heads.. problem is alot of the turbo heads are cracked now. I used the stock head off the 89 4 popper. but the combustion cambers are smaller on the n/a...
  20. mustang_matt

    Gauges Went Dead, But Car Stayed On...CPU Problem?

    sounds like one of two problems.. 1st bad bad gauge cluster or. bad harness connection.. Do a gauge test.. With your key in the off position. Push in your trip button and hold it in..turn your key to start the engine and continue to hold the the trip button until the gauges SWEEP over the...
Top Bottom
Back
Forums
Menu