Search results

  1. S

    Where to buy DC 35A Fan Controller

    I have recently bought a Mark VII electric fan for my car, and I'm in the process of getting it hooked up. However, I can no longer access the DC Fan Controller site. Is anyone else having this same problem, and if so where can I buy the controller so I can get this thing hooked up...
  2. S

    Won't Start......any ideas?!?!

    I did the 3G alternator install here a few weeks ago, but I used a set of instructions that included hooking up the two orange and black wires to the alternator. Since then every pair of instructions I've read state to NOT use these two wires on the install. When I first fired up the car it...
  3. S

    Will RPM II upper fit Performer Lower?

    I've got a quick question. Will the new RPM II upper intake fit the performer lower intake? The current upper Edelbrock Performer intake I have has all the mounting tabs broken off of it, and I've been wanting to sorta upgrade for a while. I've looked for the old Performer RPM on summit to...
  4. S

    Need Help, no oil pressure.

    I was driving home a short while ago and when I looked at my oil pressure gauge (Autometer Ultra-Lite) it went to zero. I was only about a 1/2 mile away from my house and managed to get home. I checked the gauge and wiring to the sending unit and tickered with it a bit and still no pressure...
  5. S

    Need Help, no oil pressure.

    I was driving home a short while ago and when I looked at my oil pressure gauge (Autometer Ultra-Lite) it went to zero. I was only about a 1/2 mile away from my house and managed to get home. I checked the gauge and wiring to the sending unit and tickered with it a bit and still no pressure...
  6. S

    How to Install Granatelli weight jackers and adjust them correctly?

    I just purchased some weight jackers and was wondering how to adjust them right? Do you just lengthen the bearing side to fit like stock? Do you need to get new spring isolators when installing to? Any help is appreciated. Thanks Casey
  7. S

    Are all SS Brake Lines created equal?

    I've looking into getting new SS brake lines for my car, but the partshopper is out of them at the moment. I've looked into Maximum Motorsports and Steeda, but there a little pricey for me. I've found some on ebay that are $70.00, would these work just as well? Are there any differences in...
  8. S

    Are all lower control arms interchangable?

    I've seen some LCAs selling on ebay and some of the say they will fit 87-03 and others say 99-03. Are they all interchangable or are they sepecific to the year of car? Sorry for the stupid question. Casey
  9. S

    Typhoon Upper intake fit a Edelbrock lower?

    I currently have a edelbrock performer upper and lower intake. Last week when I was putting my upper on, the back ear where the bolt goes through broke off. It ended up costing me $60.00 bucks to put it back on, and tonight when I was putting new injectors in both the back ones broke...
  10. S

    What size mass air meter for my combo? And I think I fried my 6al!

    Well I've got two questions for ya. The first is what size mass air meter do you think i should run with my combo(in sig)? I've already got a 73mm C&L calibrated for 30#ers. And I've also got a friend who is selling a 80mm C&L calibrated for 24#ers. I also already have 30# and 24# injectors...
  11. S

    Where can a find a 24# sample tube, for C&L meter?

    I'm looking for a 24# sample tube for 73mm C&L mass air meter 89-93. Where can I get one cheap or does anybody have one forsale cheap? Need one quick. Thanks Casey
  12. S

    Getting Pro-M 75mm Bullit MAM, but don't know what its calibrated to?

    I supposed to be getting a Pro-M 75mm Bullit MAM, but the guy I'm getting it from doesn't know what injectors its calibrated to and doesn't have the the flow sheet. Is there anything on the meter to tell what injectors go with it? If theres no way of telling what should I do? How much would it...
  13. S

    94-95 Longtubes fit 87-93 fox?

    Will longtubes from a 94-95 stang fit a 87-93 fox? Would there need to be any modifing done to make them work? Also I think I can get a good deal on a set of 1 3/4 inch longubes, would that big of primary hurt horsepower, rather that improve it? My mods are in my sig. Thanks Casey...
  14. S

    Longtubes and Transmission Removal

    Is it any more difficult to remove the transmission and bellhousing to change the clutch with longtubes? What kind of differences are there between switching from shorties and longtubes? What are the negatives (plug wire boots getting burned, hanging to low) and posatives (horsespower/torque)...
  15. S

    Longtube header questions (Brands)

    Have any of you guys bought longtube headers off ebay? I've seen alot going through there and they seem to be very cheaply priced. Any ideas on them, they are black, but don't list brand. They have the 1 5/8 mandrel bent primaries usually going to 3 in collectors with reducers to 2 1/2in...
  16. S

    Help! Picking new Cam

    I've recently had some problems with my engine and my cam went down the drain. I need some help on picking a new cam or getting the same one I had (Crower 15511). I don't have the money to fork out $300.00 plus for a custom cam, so if anybody has any suggestion they are more than welcome. My...
  17. S

    Need help fast!

    I was leaving college today after taking a final, and when I got into my car and started it up it was making a weird noise from the drivers side of the engine. I sounded as if the rockers were hitting the valve covers. It was pouring down rain so I had to get it home to investigate, its about...
  18. S

    Best Exhaust

    I friend of mine has a 97 Mustang 3.8 he's wanting to get exhaust put on it, and being a v-8 guy I don't know what kind of exhaust would sound best on a v-6. Would a x-pipe or h-pipe sound better, what kind of muffler, and what size pipe? Any help would be appreciated fellas. Thanks Casey
  19. S

    Need a new mod!!

    I need so input from you guys on what my next mod should be. My car just doesn't seem as fast as it should be. My mods are in the sig, I want to stay N/A so no blower, or turbo. Should I change my intake or anything like that? Thanks for input fellas! Casey
  20. S

    Car GODS enter here

    I recently put a new engine in my car. After the install I performed all the correct break-in procedures. I've found that whenever in first gear and you nail it, it cuts out and seems to have no power. After you shift into second it still wants to cut out a little and then clears up after mid...