Search results

  1. P

    Air In Fuel Line

    Here is a good article. http://www.fordfe.info/FuelTS.html
  2. P

    Air In Fuel Line

    Just another thought. If you have or could borrow a low pressure 12v fuel pump you could check the lines without pulling all them apart. Unhook the plumbing at the filter, plumb in the pump with the exit side going to a container. Connect the pump to the battery and see if it flows correctly. If...
  3. P

    Air In Fuel Line

    That was my train of thought too if it's doing the same thing since the pump change. Not an expert here but it does sound like its cavitating. I would start at one end and work to the other. Pull the sender off the tank and make sure that the filters not clogged and does not have a pin hole or...
  4. P

    Air In Fuel Line

    Is it a electric or mechanical pump? Have you checked the fuel sender unit?
  5. P

    Been a long time - Stock 351W question

    I am doing a head / cam swap in a couple weeks if you would want my old ones. They are alum heads, Edelbrock rpm generics. 2.02" intake 1.54" exhaust and around a 58cc chamber. I will have two cams and the lifters to match. One fairly mild and one with a little more thump. They are flat tappets...
  6. P

    Engine & tranny mounts

    I'm going to just try the tranny mount to see if it gets better. The 408 is not a racer but it's built fairly stout. I'm going to keep the hard engine mount for safetys sake. I had to have a driveshaft made when I put the driveline in 6 years ago because I went with a c4 to replace the fmx. I...
  7. P

    Engine & tranny mounts

    I think I'll try replacing just the tranny to start to see how much difference it makes. I wonder if the local parts store mounts are ok or should I go to a stang parts supplier?
  8. P

    Engine & tranny mounts

    I have been running the hard polyurethane motor and tranny mounts for a while. I am getting a vibration thru the car which seems to match the engine / driveline rpms. I am thinking about changing to stop this. I put these on for the strength but i am tired of the feel. I am assuming because...
  9. P

    Edelbrock intake

    I am looking at getting this carb in the link below with the Vic Jr Would a drop base air cleaner clear the choke you think?
  10. P

    Edelbrock intake

    Thanks guys. Just wanted to make sure it would work. Would love to have a shaker also.
  11. P

    Edelbrock intake

    Anybody running a Edelbrock victor jr on a 351 in a 69? Thinking about a head change and the cam guy is saying this would be the best match. Looking if there would be any hood clearance issues.
  12. P

    Short cam life with new oils

    I had mine installed 5 years ago when a lot of people were having issues wiping lobes. My guy used GM engine oil supplement and Rotella T oil. Never had an issue. Just swapped the cam 2 weeks ago to improve idle & drivability. So far so good. Gotta have that that zinc. Maybe you could switch to...
  13. P

    Paint & Body shop NC region

    Thanks for the info. I'll give them a call in the spring. Hope everything works out that I can get the body & paint done. The drive train & suspension is done with the exception of front disk which I hope to do before Febuary. Looking forward to get the exterior up to par. It still has the...
  14. P

    Paint & Body shop NC region

    I am planning on finally getting the bodywork & paint done on the sorry looking stang I have in the spring. I am looking for suggestions on a good shop within 2-3 hours of central NC. Please post any you guys feel are quality shops. Thanks.
  15. P

    Brake upgrade suggestions

    Thanks. I'll have to give them a call about the prices. I am running a C4 tranny with the Randalls Rack steering setup. I like the looks of the swap 2 but it will require a wheel size change which is ok with me. I want the tire/wheel selection with the bigger sizes. I definitely need bigger...
  16. P

    Brake upgrade suggestions

    Hey all, I have visited here often in the past and am now finally ready to upgrade my front brakes and would like input. I have a 69 Mach 1 with drums all around. Four years ago I rebuilt the front suspension back to stock and installed a 5 leaf rear spring. It still has the stock 14"...
Top Bottom
Back
Forums
Menu