Search results

  1. Exile

    Sn95' To Fox Throttle Body Tps Wiring Help

    So I am getting ready to do the Fox Mustang throttle body swap on my 95' 5.0 Mustang. Problem is I am having a hard time finding a Fox Mustang engine wiring harness that I can cut off the TPS sensor wiring pigtail with plastic connector to use... Are there any other years Ford cars/trucks that...
  2. Exile

    Some Questions About Custom Tunes

    I recently picked up a 95' GT 5.0 with the following... Rebuild 306 ci Forged Speed Pro pistons Stock intake & throttle body Ported heads with Crane 1.7 roller rockers B303 cam 30 lb injectors with matching MAF BBK cold air intake BBK headers, H-pipe, & Flows Mallory Distributor Custom...
  3. Exile

    Problems Bogging/stalling - Codes 84, 33, 13

    Well I did exactly what you said to do above. ^ Then took it for a drive, but its still doing the same bogging/stalling at times. So once I got back home I got curious and went ahead and ran the codes again. Here is what I got now... KOEO code - 11 CM (continuous memory) 11 KOER codes - 94, 44...
  4. Exile

    Problems Bogging/stalling - Codes 84, 33, 13

    I am having a problem with this fox mustang... It starts right up every time, and the motor seems to run good/smooth reving it up and down while its in park. However when I go to drive it pulls good/hard in 1st gear, but when I shift into 2nd it seems to bog/stall and hesitate a little bit? but...
  5. Exile

    Help With Egr/intake Vacuum Problems

    So my 91' Fox got totaled, but the motor/trans were still good. So I recently picked up a 89' Fox Roller to swap the motor/trans into. Well I got the motor/trans installed, and it runs good at WOT. But if your just crusin at low rpm's and try to give it a bit of gas it falls on its face like...
  6. Exile

    Engine Rolled Mustang - Proper Steps On Getting The Motor Running?

    I dont think anything has been said, or plans to be said to his insurance company. As far as the "goodies" it has the following that I will be taking out.... 306 Motor Built GT40 Heads GT40 Intake Comp Cam MSD Ignition New BBK 65mm Throttle Body New BBK Headers, BBK X-Pipe, & Flows New...
  7. Exile

    Engine Rolled Mustang - Proper Steps On Getting The Motor Running?

    Well we took the spark plugs out, turned the motor over by hand and got all the oil out of the cylinders. Filled it up with oil, put in spark plugs, and it fired right up. It smoked a little at first, but the motor "sounds good". So hopefully the motor isnt hurt. (we'll see) Now its time to...
  8. Exile

    Engine Rolled Mustang - Proper Steps On Getting The Motor Running?

    First off sorry for the long story, but figured I would get all the details in... So my buddy was out messing around in his super clean 91' Mustang GT yesterday, got it too sideways, went into a ditch and rolled the car on its roof. :nonono: The motor was still running for maybe a minute...
  9. Exile

    Manual Steering Rack

    *EDIT* - I missed the "manual" part... Make sure you get part # 22-207 http://www.oreillyauto.com/site/c/detail/A1C0/22207.oap?ck=Search_22-207_-1_886&keyword=22-207
  10. Exile

    Clutch Suggestions Please!

    I to am using the UPR King Cobra Clutch. http://www.uprproducts.com/mustang-king-cobra-clutch-kit.html
  11. Exile

    T5 Wont Go Into 1st Gear Now?

    1991 5.0 Mustang running & driving great for the last 6 months now... My buddy was getting on it in 1st gear, missed second gear, and now it wont go back in 1st gear? It still goes in all the other gears, and drives fine. It just dead stops, and wont even try to go back into 1st gear at all...
  12. Exile

    Cam Recommendations - Comp Xe270hr-12?

    Yea stock bottom end & pistons as far as I know... Yea I have the stock cam in it now... The block has not been decked, and the heads have not been milled that I know of. They came off of a 93' Cobra...
  13. Exile

    Cam Recommendations - Comp Xe270hr-12?

    I am getting ready to rebuild my motor, and would like to hear some cam recommendations for my built. I would like to stick with the 1.7 roller rockers for right now... 91' Mustang LX-Hatch (no smog or a/c) 302 (stock bottom end) GT40 Intake GT40 Heads Crane 1.7 Roller Rockers Crane Beehive...
  14. Exile

    I Need A Taller Tire?

    I have never seen any place that sells 275/50/16 tires...
  15. Exile

    Explorer Gt40 Heads Vs Cobra Gt40 Heads - Valve Springs?

    Explorer GT40 heads vs Cobra GT40 heads Im sure this has been discussed before, but I have searched, and havnt been able to find the answer... I know the Cobra GT40 heads came with upgraded Crane 1.7 roller rockers, but did the Cobra GT40 heads come with upgraded valve springs? If so what is...
  16. Exile

    Drivetrain Speedo Gear? 87 Gt, T-5z, 3.55, 255/40/17

    3:55 gears take a black 20 tooth speedometer gear. http://www.latemodelrestoration.com/item/LRS-17271B-K/83-95-Mustang-20-Tooth-Speedo-Gear-Kit-Manual
  17. Exile

    How To Restore A Fox Mustang 5.0 Intake Cover/plate

    Very nice! Whats your methods in polishing these things if you dont mind me asking??? Do you sell them?
  18. Exile

    Ticking, Smoking, Low Oil Pressure, Distributor/cam Gear Not Turning

    What could be causing the low oil pressure problems? It looks like a fresh build besides the reuse of the stock heads, which im still not sure if any work was done to the heads by the previous owner before adding the E303 cam. Failing oil pump? Rings?
  19. Exile

    Ticking, Smoking, Low Oil Pressure, Distributor/cam Gear Not Turning

    My buddy recently picked up a 1989 GT Mustang, and is now having some problems, and needs a lil help... 302 + 5-speed E7 heads (unknown whats been done to them) E303 cam Trick Flow upper & lower intake A/C & Smog delete Long tube headers Electric Fan The car runs good, but a few days after...
  20. Exile

    Best Combination

    Well I would consider upgrading your intake to a GT40 intake (or better) to match your combo, as well as a 70mm+ MAF sensor to match the 24lb injectors.