Search results

Over the last week or so I've noticed that my pinion seal is leaking. I wanted to take this opportunity to put in some new gears because I drive it every day and some better mileage would be really nice. Does anybody know a good shop in the San Jose, Ca area that could help me out for a good price?

So back in December I installed a firewall adjuster because the previous owner had installed a dual hook quadrant and no adjuster. About a month and a half later, the clutch cable broke. I replaced that and adjusted that to where I like my clutch. Last week I was driving to work and I was...

So yesterday I changed the transmission fluid because the previous owner was running straight gear oil. I filled it up with Dexron III like the manual says and now it grinds 3rd and 4th when down shifting. Any ideas?

I have a steering wheel out of a '90-93 fox complete with the shroud and airbag unit. Pics upon request. $40+ shipping from 95123 or trade for a9l, a9m, a9p, a9s etc for mass air swap.

So I've been chasing this problem for about two months now and I've been slowly replacing parts that needed to be replaced. At a cruising speed, no matter the speed, if I roll onto the throttle there will be several loud pops that sound like misfire. After the pops, it sounds/feels like a...

I don't know if any of you guys have seen this yet, but someone posted it over on Reddit. http://imgur.com/a/bYkwF It's something up there with what madmike would do. Pretty friggen sweet if you ask me.

So I've been having a problem with my amp that just started last night. I'm not sure how you all are with these sorts of things, but if I've leaned anything about this forum, someone will come through. :nice: So I have a 400w, dual channel amp powering 2 10" subs. They were installed about 2...

So I found this while trolling craigslist today. Could it be made to work with our 5.0's? http://sfbay.craigslist.org/eby/pts/3515579686.html

So I just ordered myself a firewall adjuster from AM, should be in tomorrow. I love christmas time shipping prices. :D My question is: Since I already have a double hook quadrant, when I install the adjuster, which hook should the clutch cable go on?

Anybody have one laying around?

Any idea what these leads might be for? Discovered them last night in the trunk while wiring up a sub woofer. One is Orange and black, the other is Green and Yellow.

So I'm pretty sure I have a thermostat stuck open, just wanted to throw it out there for some feed back. The temp gauge never really comes up to temp from cold, except when sitting in traffic. It does have a 3 core radiator (brand unknown). Also, I get mildly lukewarm heat from the heater that...

So my '87 came from the previous owner with the wheel off of a '90 or later car. I got the correct wheel and went to mount it up today. When I got the old wheel off there was all the stuff for the newer wheel, but the wiring harness was not hooked up, for obvious reasons. So my question is, what...

So I know I might get flamed for this post, but what can I expect from a MAF conversion in terms of power and economy. I can list my mods if that helps...:shrug:

So I had a buddy of mine wire up a radio tonight. Now my tach doesn't read and the dash lights won't come on. I checked the interior lights fuse and it is all good. I'm not the best when it comes to electrical so I need some help... EDIT: Talked to the guy who installed the radio, said he...

Does anybody know if axle carrier bearings must be pressed in? Or can they be dropped in?

So does anybody know what a bad throw out bearing sounds like? I've got an annoying sound coming from up front while driving and it goes away when the clutch is in. Thanks for the help

So I'm getting a really nasty whine/rubbing/grinding noise while driving down the road. It completely goes away with the clutch to the floor, which leads me to believe it's the throw out bearing. But a friend of mine said pilot. Any ideas?

One question for the techies, my idle is a bit erratic. It likes to stick high, around 1,500 rpm. And sometimes it wants to drop to 500 rpm and stall out. Easy fix?

Hey all, Just here to introduce my self and my car. I just bought myself an '87 GT, been in the Mustang ring for a few years now. This one is my first time owning one. According to the PO she has an Edelbrock upper and lower intake, 75mm throttle body, EGR spacer, 9mm FRPP wires, and a few...