Search results

After selling my 1992 LX Coupe back in 2003 and have been waiting for just this type of Mustang to return. Just ordered a fully loaded, 50 Years, Ingot Silver, 2015 GT Premium, w/GT Performance pack and Manual trans. There's an 8-12 week wait time until it arrives and I've already been...

I just paid 35.00 for 5 of them Power Windows, Power Steering, Air Conditioning, AM / FM Cassette, Power Brakes, Tilt Wheel, 6-digit Odometer Safety Options 4 wheel ABS, Dual front air bags/active (manual) belts Vehicle Information: 2001 FORD EXPEDITION XLT VIN...

2001 Expedition...wondering if there have been any reported accidents...

1FMPU16L11LA70435 Thanks!!!:flag:

Hod on a second now. your sig says your best was a 13.029 @ 109. What's the truth? BTW Nitrous kits typically do slow you down. First off without an MSD timing retard, PMS, Tweecer etc... you will have to back off 2-4 degrees. Secondly you usually run one to two ranges cooler plugs...

I need a part number. The piston must fit a stock rod and give @ 10:1 comp ratio w/ 61 cc head. I've looked on Summit's wab site but it's not very descriptive.

Okay I What ring gap should I use if I plan to install a 6 psi supercharger? It's a 331 and I'm using Probe pistons and file fit rings. The instructions with the pistons aren't very good. I've read in Ford Muscle articles: .0045" per inch diameter for the top ring = 4.030" x .0045" =...

I am going to file my own rings this time because the machine shop screwed them up royaly. I am going to purchase some speed pro moly rings. I know the technique I just need so help on the actual gap for 306 ci. NA motor with a forged piston. Thanks in advance, Chris

Sorry if that got under your skin. I wanted to provide a little entertainment for you so I made sure to make it very unbelieveable. Sorry if I crossed the line. Chris

Oh $hit dude!!!!! Bad News – This vehicle does not qualify for the CARFAX Buyback Guarantee! Severe problems (major accidents, fire, flood damage, major odometer problems or lemon history) were ever reported by a Department of Motor Vehicles (DMV) for this 1989 FORD MUSTANG GT...

Certainly, but 30's would be preferred.

Yes, that or for some VERY odd reason a vaccum line was unplugged.

Well the cam is good, it's the stage 1 cam. I have the stage 2 and it works very well for me. IF you're going to do the cam you might as well do it all at once, cylinder heads, intake manifold, rockers (pushrods if necessary) ARP hardware, new water pump, gasket set, headers etc. DO not...

1HGCD5655RA021825 Thanks in advance!

I just thought that the fresh air might just be a method of providing the cats with an external source ambient air to assist with the chemical conversion that takes place. Just making sure I don't ruin a $400.00 x-pipe :rolleyes:

I am finally going to do something about these fumes. My wife will not drive the car because she says I stink of fumes when ever I get out of the car. I currently have BBK 1 3/4" LONGTUBE headers, offroad H-pipe (no cats) & full exhaust w/tips. I'm going to buy the BBK-1662 shorty x-pipe...

That's a good question. My old engine had blow-by into the crank case that would push oil out the front and rear main seals and it had compression between 164-187 psi. My only explanation would be that the ring gap was obvioulsy incorrect and that my old engine builder sucks.

exactly, I went through it too. I had the top of the line flaming river set-up that they claimed was great for street driven cars. BULL f-kin $hit, what a pain in the arse. So I got a brand new 15:1 AGR rack and a new stock pump and I love my car again!!!!! Also, I could not perseive a...

I have the TFS stage 2 cam and Omega rockers. The cam is very similar to yours if I'm not mistaken. Just how loud is yours? Mine isn't too bad. You can just hear it with the hood closed at idle. My AFR heads do have an allignment problem though. Some of them are as far as half the...

Yea I'm wondering if the steeper cam profile adds to the noise. I too have the clacking rockers. Especially when the idle is between 1100 - 2500 rpm. I've tried 1/4 1/2 3/4...all after zero lash and after the car warms up it begins. I'm going to try a 20-50 oil to see if that quiets...