Search results

  1. Champ10187

    PLEASE HELP just installed UPR coil overs and they rub on 245 tire!

    can you further explain the camber bolt. im gonna talk to UPR's tech guy on monday and see what he has to say but so far looks like im gonna be returning them.
  2. Champ10187

    PLEASE HELP just installed UPR coil overs and they rub on 245 tire!

    im running 98 cobra wheels (17X8) what should i recheck i cant think of how anything could be installed wrong cause everything only bolts in one place???
  3. Champ10187

    PLEASE HELP just installed UPR coil overs and they rub on 245 tire!

    As the title says i just got done installing UPR coil overs, strange struts and MM caster camber plates and when i went to finally put the wheels back on they rub on the inner part of the tire. Should i have known before hand these werent going to work or is it something i did wrong. Please...
  4. Champ10187

    Help me create the "Surging Idle Checklist"

    could a bad ground be cause for idle problems?
  5. Champ10187

    Detroit Area Mustang guys

    hey im about to get mustang tuned, mods listed below. I origially had it done at alternative but since they have switched over form autologic to SCT they $600 to redo the whole thing. I currently have an AUtologic chip so i was thinking about getting it redone at Walsh motorsports just wondering...
  6. Champ10187

    cant get idle below 1000 rpms

    I just threw a new motor in my car which includes a vortech s-trim and when i started it up the idle was real high like 1500 rpms. When i go to reset the idle with the IAB disconnected it starts to surge up and down. at 1000 rpms its steady but as soon as i turn the idle screw to drop it anby...
  7. Champ10187

    T-5 whines in 2nd, 3rd and reverse

    i just installed a whole new drivetrain in my car out of a 93 mustang 5.0 with 19,000 miles. I just got done driving it for the 1st time and the transmission has a loud whining/howling noise in 2nd, 3rd and reverse. The noise gets louder as RPM's go up and it is always doing it, even when im...
  8. Champ10187

    Fuel Pump not always coming on.....causes??

    ok, i tested all the terminals on the fp relay and they all have power when the key is turened on. i checked the two wires for the inertia switch and neither have power. the two wires for the inertia switch are brown and green, not red and red/black.....im so confused. none of the colors match...
  9. Champ10187

    Fuel Pump not always coming on.....causes??

    jrichker, its asks to test all those different colored wires but where are they located. i thought they were the wires at the fuel pump relay but when i just went out there, none of the wires at the relay matched up with the wires it asked to look for in your post. where are these wires? could...
  10. Champ10187

    Fuel Pump not always coming on.....causes??

    hey jrrichker, thanks alot. this should really help. can i do all this with just test light or should i get a voltmeter?? thanks alot everyone, time to get to work. btw, how can i figure out which one is pin 22??
  11. Champ10187

    Fuel Pump not always coming on.....causes??

    Sometimes when i go to turn the ignition the fuel pump does not get power (doesnt prime and car wont fire). Sometimes its fine, then others they just dont get power at all. it seems kind of random. what could cause this? Bad relay...??
  12. Champ10187

    vacuum diagram for upper intake manifold

    heres a pic of the hose. its making a loud hissing noise so its obviously a big leak. it comes out the back of the upper intake. the left side of the pic is the firewall the right side is the upper intake. hope this helps.
  13. Champ10187

    vacuum diagram for upper intake manifold

    bmorris, thanks for the pic. according to the diagram the one dissconected is the MAP sensor line. where is the map sensor, why would it have been disconnected. this engine has all emmissions and EGR stuff either removed to blocked off. i'll try and take a pic of what it is im trying to...
  14. Champ10187

    vacuum diagram for upper intake manifold

    After installing a new motor i now i have a vacuum leak and found that its something coming out of the upper intake. i can figure out what it is or what plugs into it so could someone post a pic or tell me what all the vacuum lines in the upper intake are for. the specific one im talking about...
  15. Champ10187

    just installed new motor and idles high

    no i did not have to take off the intake. I changed everything basically, fuel fuel lines, all harnesses and computer. It is the stock computer but it has a chip in it tuned for the engine combo. And yes i do have a bypass valve for the blower. i'll try the carb cleaner and let you know...
  16. Champ10187

    just installed new motor and idles high

    no the idle does not seem lumpy at all. there is hissing noise coming from the back of the intake...right between the intake and the firewall. Are hissing sounds signs of a vacuum leak?
  17. Champ10187

    just installed new motor and idles high

    im almost positive thats not it cuz why would it be fine before the swap. i unplugged the selenoid and the idle dropped to about 1000, that means its working, right?
  18. Champ10187

    just installed new motor and idles high

    I just installed a compplete drivetrain and wiring harness (computer and everything) out of a wrecked mustang. Ran perfect and idled perfect before i yanked it and now when i start it up it idles from 1300-1400. lowest i could get it was 1100 and that was by turning the idle screw all the way. I...
  19. Champ10187

    AEM Engine Management System?

    go to www.turbomustangs.com and them click on Project Car. That guy did a complete install and review of the AEM engine management control.
  20. Champ10187

    Idle jumps up randomly when I come to a stop

    i just realized that it only does it whne the A/C or heat is on....what is the reasoning behind that? I checked the fuse and its good, the light is solid..