Search results

No plans on racing. Took supercharger off a couple years ago. Thought it was an open differential since only the wheel I was moving would turn. Good to know it already has traction lock. Bad not to have experience to do it myself.

I noticed that American Muscle has stopped selling the 8.8 28 Spline Ford Racing Traction Lock Differential. I am planning on upgrading my 2000 Mustang GT Automatic to a Traction Lock and 3:73 Gears. Is there any reason to incur the additional expense and upgrade to 31 Spline Unit. The car is a...

Thanks!!!! Glad I asked. My U joint has been slapping around and I have been getting some vibration around 80 MPH. Car has 120K, so the upgrade is warranted.

Sounds simple enough, So the length of the shaft is not the problem - just the yoke? So if I order new Shaft and manual yoke there should be no fitment problems?

Trying to find an Aluminum Drive Shaft for 2000 Mustang GT Automatic. Most of the Drive Shafts I have reviewed are for Manual only. Part number would be helpful.

That is exactly what I am looking for. Most likely will have to get re upholstered. If the pic uploads, here is what I have done to interior so far. The panels were taken out, cleaned, roughsanded, primed painted and clear coated to match exterior pait. All came out ok, but had some difficulty...

Thanks for the info. I guess my best option is to have them reupholstered.

Anyone know what type, if any, modifications need to be made to make rear seats from a Cobra Coupe fit A 2000 Mustang Convertible? I am shopping around for two tone seats. I have only seen two tone Cobra Seats on Ebay so far. New Upholstery would be an option if I could find the right product at...

I just replaced both front wheel hubs. I went to Ford Dealer and asked parts department for two wheel hub nuts and caps. The manual says that both have to be replaced. The parts guys said he rarely sells these and the repair department just uses the originals. So I reused the original. I haven't...

I am selling my AED Supercharger setup. It uses a ported M-90 blower underneath an aluminum intake manifold. The set up will come with Blower Unit, Intercooler, hoses, electric water pump, 42lb injectors, 80 Ml MAF, Original installation instructions. The unit is in great operating condition...

Has anyone ever seen, installed or know of a speaker that can fit onto or in a light bar for a 1999-2004 GT Convertible?

THANKS:flag: I have plenty of morot oil. Going to put it back together now.

Any ideas of what to use to lubricate the o rings on some brand new injectors. Autozone didn't have anything and told me to use KY or Vaseline. Don't have need for either one, so not in the house. Does that sound right??? Any other suggestions? Dielectric grease, lithium grease?

WHOA!!!! do not spend that amount of money. You can go on Ebay and find a complete unit with brackets and thermostat for $189.99. shipped free. I recently bought a "Ford Racing" Manifold from Toulsey Ford Parts Tousley Ford Parts Depot Their unit is less, but you have to buy intake manifold...

Definiely will do that in the morning. Also checked out the Sears Tool catalog, I think they might make a wrench that has a right angle on the end.

Were you able to get to it just from removing wheel and fender liner? Or did you still need to use your homemade wrench? Does dropping the x pipe give more clearance?

Is there a special tool or method for replacing the EGR Tube on the 2000 Mustang GT. I cant get my arm to the nut from on top of the engine and I cant get a wrench into the area from underneath. I am thinking I might have a little more room if I disconnect the XPipe from the Exhaust manifold...

Since having problem with drip rail, i had stripped the car down to metal. I did some extra sanding on the drip rail lip to make sure i could get moulding to fit. Paint shop, primed and sealed the drip rail area, installed the drip rail, taped it and finished painting the car when ready. They...

I bought a Strut Tower Brace off of E-Bay last year. I appears to be powdercoated silver. Right now I am getting a lot of rust showing through. I have polished several times and have decided that it needs to be painted. Can anyone suggest best prep and materials to paint over this surface?

Here is the build on the engine. Probably not your standard Engine rebuild. Does this change anything you have provided before? Thanks for response, I'll be taking valve covers off tomorrow to check it out. # Part Number Description 8 KB115-60 Pistons 1 2271-60 Grant...