Search results

  1. 5

    650 or 750 Carb For My 357, That Is The Question!!!!

    Hi, I have been trying to figure out what is going to be the best carb to buy for my 357. Right now Im using a friends 825 demon and it is obviously too big. Here is my combo: 351 .30 over, stock bottom end with girdle, je pistons, out of the box Track Heat heads, Stage 2 Trick Flow Cam...
  2. 5

    Blown Head Gasket Fixed, Engine is All Screwed Up Now

    Yesterday I was spraying a 100 shot on my car and when I was done, the car was acting very wierd. For one, it got very hot like never before. Two, it wouldn't idle and didnt want to start for crap. So, I pulled the dipstick and sure enough it was milky. Today I tore the motor down and put ion...
  3. 5

    GT40 X Aluminum Head Motor Setup Question

    I'm getting a bunch of parts for a good deal and have a few questions about the setup. These parts will be going on a stock shortblock with good oil pressure. The setup will be GT40X aluminum heads, Trick Flow Street Intake, Ford B or F cam, 1.7 roller rockers, 70mm TB, 76mm Mass air meter, 30*...
  4. 5

    Differential from Ranger Same As from 5.0 Stang???

    I blew the differential up in my 8.8 rearend. I could just put a completely new rear in there but a friend of mine says I can just put the differential from a Ford Ranger in there. He says even though the actual casing is different (longer driver side axle) that the differential is still the...
  5. 5

    Motor is running crappy after check engine light comes on, Any Ideas?

    I got my used 302 HO running pretty well, timing is at 12 degrees with 93 octane, tps set to .99, idle at 700-800 rpms, etc> My problem is this. The car runs strong and is making good power for a stock motor with exhaust but the check engine light always comes on after about 10 minutes or...
  6. 5

    New motor in car, It wont Start HELP ASAP!!!

    !!!!!!!!!!!CAR IS RUNNING!!!!!!!!! I changed the injector wiring harnees with the extra one my friend gave me and it started right up. It runs pretty damn good to. I got it all running good, took it out and ran right with some convertible LX on the street. he had P heads, cobra intake, b cam...
  7. 5

    New motor in car, It wont Start HELP ASAP!!!

    I checked the firing order through the valves and it is a high output motor. Yes, it ran fine before the swap. I'm using the 91's, harness right now. I got another injector harness from a friend last night and I'm going to try that later today when I get home. I don't really think that will...
  8. 5

    New motor in car, It wont Start HELP ASAP!!!

    OK, I will do that but it has a high output intake on it and it had the wires in the high output order so wouldnt that mean it is a high output motor? If I dont figure this out soon, i think I'm going to throw a carb on the damn thing!
  9. 5

    New motor in car, It wont Start HELP ASAP!!!

    Well I just put another set of injectors in and it is still only getting fuel to two cylinders. I pulled all plugs and only 1 and 3 had fuel on them. I have fuel pressure, have checked all fuses and fusible links, pretty much everything. The fuel is just not going throught the injectors and I...
  10. 5

    New motor in car, It wont Start HELP ASAP!!!

    Well I got my starter issues fixed, it was a bad flywheel, so now my starter is good atleast. The car still wont start though. It is kind of hitting, and it almost starts but it doesnt. I pulled the number one plug and it has fuel on it so I know it is getting fuel there. However, I pulled...
  11. 5

    New motor in car, It wont Start HELP ASAP!!!

    I finally got it to start after spraying a lot of ether into it and then it just died a few seconds later. It sounded like crap too. It was real irratic and sloppy sounding. Then my starter went out so I put another starter I had in and it just died too. Every time I crank it over it sounds...
  12. 5

    New motor in car, It wont Start HELP ASAP!!!

    Well when I took the plugs wires/cap rotor off this new motor they were in the high output order. That is how it was when it was pulled from the other car. I will try the other order tomorrow though just to make sure.
  13. 5

    New motor in car, It wont Start HELP ASAP!!!

    Yes it is a High Output motor for sure. I was told it ran and I saw the car it was pulled out of (totaled in the rear end). It came from a reputable salvage yard and I'm pretty sure the motor will run, I just cant figure it out. Could my computer of went bad while the car was sitting? It only...
  14. 5

    New motor in car, It wont Start HELP ASAP!!!

    :shrug: :shrug: I just dropped a stock 302 HO in my 91 LX because the old motor spun a bearing. This is a stock 302 out of a 90 Lincoln, it is exactly the same as a mustang 5.0. I used all the accessories and wiring from my 91. Everything works and it cranks over but will not start. I re...
  15. 5

    95 GT to Cobra Clone, Need Information

    That was the plan, I know it sounds cheesy but I'm not going to half ass it. I really want to do every possible thing so the ONLY thing it wont hve is the paperwork. The engine doesn't matter though because it will be getting a built 306 or 331 whenever I do the motor. And I know everyone...
  16. 5

    95 GT to Cobra Clone, Need Information

    Hi, I'm buying a really nice full option white on tan leather 1995 GT. It is a 5 speed and I want to turn it into a full Cobra/Cobra R clone. It already has a Cobra R hood, Cobra front bumper(no fog lights), 95 real Cobra R wheels, white face gauges, and that is it. With the Cobra R hood and no...
  17. 5

    Car Finally Runs, But Runs Very, Very Crappy!

    I just got the upper intake off so I can adjust the roller rockers again and I could smell gas real bad when I took the intake off. The back four runners of the intake were damp with raw gas and the upper to lower gasket was soaked with gas on the last four runners. Why is there so much fuel...
  18. 5

    Car Finally Runs, But Runs Very, Very Crappy!

    Bump!
  19. 5

    Car Finally Runs, But Runs Very, Very Crappy!

    We finally got it to idle, or atleast somewhat idle and I'm able to leave the valve cover cap on now. When I push in the clutch, it slowly drops down in RPM's and finally will idle at about 800 RPM's but it is very rough. It doesnt die though. It has very small intake backfires every once in a...
  20. 5

    Car Finally Runs, But Runs Very, Very Crappy!

    I have a PCV Valve hooked up. The idle is turned all the way up until the screw wont turn any more. I'm stumped.
Top Bottom
Back
Forums
Menu