Search results

  1. 4.6_02_Black_GT

    Please post pics of your lowered 96-04 GT's

    Heres mine, Steeda tie rod ends, MM shortened sway bar links, MM CC plates, Eibach Sportlines, Tokico 5-way Illuminas.
  2. 4.6_02_Black_GT

    Quick amp question

    Hunter your post is a little unclear. But if I understand you, you are asking if your amps(stereo) are powered on, but you not actually have a singal going to them. Will you have more amperage available to your electrical system. Well I'm not sure what you are getting at.. but the answer...
  3. 4.6_02_Black_GT

    Couple of ??? about wheel/tire size!!

    18 x 9.5 all four corners, Eagle F1 GS-D3's 275/35/18 5/114.3 35mm offset 26.6 pounds each(rim only)
  4. 4.6_02_Black_GT

    LOUD engine noise

    Chrome,. Sorry to hear bout the engine, do you think there was problem with the intake gaskets, do you think your engine ingested coolant or did it get in an oil passage???? Is that was caused the thrown rod?? Two good choices below, VT short block list better components, but the DSS block...
  5. 4.6_02_Black_GT

    '04 gt already knocking?

    I get a little valve train noise just after starting. It goes away after a few minutes. 2002 with 50K miles. Noisy lifters :)
  6. 4.6_02_Black_GT

    HELP!!!!

    Four-Six Just to clarify for our Steeda rod ends(see my pic below) do not require any maintaince other than peroidically wiping off road grim...Thats the beauty of Heim joint. A any lubricate you put on them will only attrack more road grim and dirt and girt..again..maintaince free...
  7. 4.6_02_Black_GT

    dimming Lights

    You mentioned your voltage is at 12 volts, is this at idle or 1000+ rpms?? If you r engine speed is anything north of 1000 rpms the alternator should be able to deliver a constant 13.5-14 volts back to the battery. If the alternator is new and you know its good, I would possibly check your...
  8. 4.6_02_Black_GT

    timing belt

    Killer EX Heres pics of the parts to replace Killer the tensioners have a spring that wears out and causes you chains to go slack...and of course the plastic guides just wear out from chain rubbing on them. Dont forget to do the chains too.
  9. 4.6_02_Black_GT

    timing belt

    Killer EX, The 4.6 does have timing chains...on the GT motor the crank drives both chains for each bank of cylinders. The chains and sprockets are metal ....but the problem is that there is a set of followers that presses in from the outside of the chains to keep tension on the chains so...
  10. 4.6_02_Black_GT

    HELP!!!!

    if its really making a grinding noise there must be contact somewhere, have you checked to make sure your rims are not rubbing on the swaybar??:shrug:
  11. 4.6_02_Black_GT

    which ATF for 3650

    lousiana, Old fluid looks nice..just slightly dark, how many miles on the old fluid??
  12. 4.6_02_Black_GT

    Anybody know what this thing is?

    vibration damper....)(offically mot bar) with 4.10 and aluminum driveshaft...mine has been gone the day I had my gears installed.
  13. 4.6_02_Black_GT

    Which tires , after SC Power is down :)

    LvnMustang, yeappers I run 18x9.5 on all four corners, Heres where you can get the rims They are ADR M-Sport rims, in statin finish..they make a hyper black finish and chrome finish. ...unfortunately in 18 inch..nothing wider than the 9,5 inches I have. There are several places online to...
  14. 4.6_02_Black_GT

    Which tires , after SC Power is down :)

    here's my Goodyear F1, GSd3's.... 275/35/18 all four corners... best combo of dry wet tire made :D :D :D
  15. 4.6_02_Black_GT

    Speed calibrator?

    TJ try this link, Speed Cal from Dallas Mustang :nice: :nice: http://www.dallasmustang.com/page/products.php?product=9910
  16. 4.6_02_Black_GT

    Fix your Slow dropping/hanging RPMs

    okay one more time, small hole on the drivers side on a 02GT right?? Is this correct?? seems to make sense
  17. 4.6_02_Black_GT

    flame thrower

    crazy stang, Dont you have to have some kind of fuel source for those spark plugs to light, if you 01 is working correctly you will not be rich enough to do the flame thing... To work I assume the kits need to richen your fuel/air somehow, so there will be some gas to burn:shrug: :shrug...
  18. 4.6_02_Black_GT

    Fuel Cell Help

    PonyBoy love the fuel cell setup looks great:nice: :nice: Looking change my 2002 GT from returnless to a return system(regulator by-pass), so I', looking to go fuel cell or mod a stock tank with a sump. Just two questions how much did the fab on the new steel floor cost you?? I dont have...
  19. 4.6_02_Black_GT

    Fuel return line?? Fuel sump or cell how to??

    Need ideas on how to fit, an AN-10 outlet and AN-10(or 6/8) return port on our stock gas tank. Has anyone had an aftermarket sump welded into there tank(a sump with the outlets)?? Or is everyone using new fuel cell that came with proper outlets and return?? Are you mounting the new cell in...
  20. 4.6_02_Black_GT

    Where is the computer on 2002 GT

    I know but if I tell you I will need to kill you:rlaugh: :rlaugh: :rlaugh: :rlaugh: :rlaugh: seriously...passagner side kick panel down where your feet go.