Search results

  1. H

    4v Swap/Tuning???

    I'm using the SCT software anyway. Sorry. Tim
  2. H

    4v Swap/Tuning???

    I'm currently doing a swap to an 03 Mach I 4v. I'm using the return style fuel system and my 98 EEC. I'm reflashing the computer with a stock 4v tune and will begin my performance tuning from there. Your problem IS in the tuning. You don't need to swap computers. You only need to have a...
  3. H

    315's?

    That is what I had to do. Tim
  4. H

    gear installation question

    That is the installation kit. I'd get it, because you don't want to be in the middle of the swap only to find out you have a shot bearing or destroy one when you're pulling it off. I'd rather have too much than not enough when I install gears. That's one place I don't mind having extra parts...
  5. H

    Need help!

    I'm shooting in the dark, but I'd say the converter unlocking and locking? I've never had it happen. Tim
  6. H

    315's?

    I have a set of 315s on 10.5 inch rims. They wouldn't fit with the quad shock, but I have LCAs so no problem there. They also come close to the exhaust if it's pulled too far forward. 315 Nittos will fit on 9 inch rims, but I wouldn't go with any other brand unless you have a wider rim. Tim
  7. H

    Quick Question On Timing A. install

    It sounds like marbles in a can. You cannot mistake the sound when you hear it. It sounds nothing like a normal engine sound. If you hear it, get off of the gas. Tim
  8. H

    Quick Question On Timing A. install

    I would suggest you start with 14 and work it up as I stated in the previous post. What works on someone else's car may or may not work on your car. Taking a blanket statement of what worked on someone else's car and applying it to your car is asking for trouble. You may set it to 16 on 93...
  9. H

    Quick Question On Timing A. install

    The o/r h-pipe doesn't make you run rich. It just smells like it, because you no longer have cats. I typically ran 14 degrees on 92 octane. The rule of thumb is to take it up til it detonates slightly then back it off a degree or two. With the T/A, you should really be running the highest...
  10. H

    Is my Master cylinder bad?

    Have you tried bleeding the brakes? If not, try that first. Tim
  11. H

    B&M Hammer Shifter for 4R70W

    Nope. They changed from AODE to 4R70W in 96. Tim
  12. H

    Injector colors

    Mine are definitely FMS injectors. I found the following on Corral.net: 19's - Orange 24's- light blue 30's- Red 36's- Dark blue 38's are Lucas only and are black 42's- Lime Green 42's Lucas are black with a green band It also appears Ford colored the 03s blue (42lbs) for some reason...
  13. H

    Injector colors

    24lb injectors are blue. 30lb injectors are red. I have 42lb injectors and they're flourescent green.
  14. H

    B&M Hammer Shifter for 4R70W

    BTW, the shifter is cool as hell. Tim
  15. H

    B&M Hammer Shifter for 4R70W

    I just looked at my instructions and it doesn't mention the 2001s. The OD button is actually located down around the boot area, so I don't think that's it. My recommendation would be to call the Horse to get it from their mouth. Tim
  16. H

    Injector colors

    Orange are 19lb injectors. Injectors are not mods for hp. You only need to change injectors when you start pushing 100% duty cycle on the injectors you have. Typically, the 19lbers are good for about 300 bhp. Tim
  17. H

    Detonation problems

    After looking at your sig again, I don't think it's timing. I used to run 14+ with no issues. Check the gap on the timing adjuster. If you're running Bosch Platinum 4s, I've heard of people having issues with them. Whiter plugs is a sign of the car running lean. Tim
  18. H

    Detonation problems

    Do you think you might be running too much timing? I'd back the timing off a little and see what happens. You may have some bad gas. Also, check the gap on the timing adjuster. If it's too loose, it'll detonate. Tim
  19. H

    What to do

    Just my $.01 here, but with $900 you're limiting yourself to (2) or (3). I wouldn't let some guy do my heads (even if they have a flowbench). I would only let one of the "big" guys touch my heads. These heads aren't the same as pushrod heads. The same tactics don't necessarily work. If it...
  20. H

    Best x pipe??

    Dr. Gas without a doubt. Tim