Search results

I want to have a pair of 17x9 Bullitts cut down to take a 205/45x17 tire. Anyone know of a shop that does this? We have none in the Albuquerque, NM area. I want the narrowest 17 I can get up front to go with the 17x10.5 Bullitts and 315/35x17 BFGs out back.... Wayne

Ford Parts Network lists two different numbers: F1SF-AA for 94-95 F2SF-CA for 94 Which one is correct or will either work. Difference is 2 bucks... Wayne

According to their web site they make a direct fit 2 core unit for the 94 with automatic transmission. My concern is that with a Vortech installed that it will not fit. Does anyone have one with a set up like mine and was it a direct fit? Wayne

:shrug: After putting the new engine in and firing it up (ran smooth and quiet), the air bag light is flashing. Ran a code scan and system test passes, no codes. Any ideas? :shrug: Wayne

Anyone know if ProStars or Draglites (normal or Xp) in 15x3.5 with 1.75" BS will fit over Bullitt/Cobra 13" brakes? Wayne

Anyone know the dimension (L x W x H) of the stock oil pan. I'm looking at replacing mine to clear a main girdle but am concerned that since my car is lowered some of the aftermarket 7 qt pans may be too tall or extend to low. Wayne

Have a chance to get a CHP 347 for the same price as my 306? Would I be stupid not to? Wayne

What's the best way to break in a new shortblock on a supercharged car? Thanks Wayne

<marquee direction=right> :banana: :banana: :banana: </marquee> Just ordered my SB today. Was wondering how many CHP 306 owners are out there and what you think of yours? Thanks. Wayne

Getting a softcode 124: TPS voltage higher than expected. I looked at the datalogs and TPS voltage ranges from .994 to 4.87. Did a quick datalog KOEO to see if the TPS was noisy or going bad and it isn't, I'm getting nice clean linear voltage and no apparent flat spots. Didn't have this...

I bought the Model ED-5004 which was supposed to fit 302 to yr 95 but another guy said I had the wrong one. Anyone have one and which model #?] Wayne

Took car to "The Dyno Edge" today to make sure we had safe A/F. Only made one pull because we need to lean out the top end and I want to keep the FMU so I need to get some ratio disks for it. Motor was rich and loosing power from 5600 - 6600 (10:1 A/F). Made the numbers on 14 psi. We figure...

Got these codes after installing my AFM Vortech S-Trim stg I kit. I've gotten the same codes wether I'm using the stock W4H0 binary or my JMS tune. 511: Electronic Control Assembly (ECA) problem, Read Only Memory test failure. 124: Throttle Position Signal voltage higher than expected...

Finally got some pictures of my new AFM Vortech S-trim Stg I kit. To say I'm stoked is an understatement. Wayne

After installing my AFM Vortech S-Triim kit car had intermittent and sporadic check engine light only at normal temps. I't doesn't matter if I use the stock EEC tune or my 3 JMS tunes. Doesn't matter if your driving around town or at highway cruise, light comes on or goes off at different...

Have 24# and ProM 75 Bullet w/24# cal along w/MAC CAI to sell. Would like to sell injectors and MAF together. Inj and MAF $200 MAC CAI $60 Removed when I installed my Vortech. Wayne email: [email protected] Albuquerque, NM

Anyone have one the want to sell and if so how much? I broke mine and need it to pass emissions. email: [email protected] Thanks Wayne

Looking for pics and ideas on where/how to mount a battery disconnect switch for my trunk mounted battery next week. Wayne