Search results

Is my head cracked? There was alot of oil in the coil and plug chamber on my #6. Thi is a 99 GT by the way... What do you think I should do? Need help ASAP as this is my daily!

Sometimes while driving at night my headlights will flicker...this is scary. I do not know how they stop doing it, but they just do. Is there a specific wire that could be loose or something in the switch?

Hi, I've been driving a 99' GT with 120K on it for about a week, and when it is cold it sputters under load. In first, I have to let the clutch out at high RPMs so it doesn't sputter. When I am coasting with the clutch in, the RPMs slowly fall down under 500 then die. I am a 5.0 kinda guy so...

I was going down the interstate the other night and my headlights went off and then started flickering. The dash lights stayed on though. I kept pounding the area on the dash where the switch is and they stayed on...I checked the switch today and didnt find anything weird. What wire should I...

We are restopring a 70' Mach 1 and the speedometer cable and stuff in there is broken. How do I remove it? The areas around it seem to be riveted together, I'm sure there's an obvious solution here. Thanks.

Running into some cash, want a 347 kit. I've looked on ebay and there are prices ranging from 789.99-1,125.00...ANyone know who sells reliable kits and who does not? is this "piston pin intersecting the oil ring groove" just jibberish? I've seen "nodular iron" cranks, is this a reliable...

Just wonderin because my car's left side suspension area rattles when I hit bumps. I had my front struts replaced but that didn't fix it. Also, could a bad tie rod end cause uneven tire wear?

Hi, my PS pump makes alot of noise, the pulley wobbles, and it leaks. I'm replacing it tomorrow. Are there any special tools I might need to complete the job. I have access to a garage tomorrow so tips asap would be great. Is there anything complicated about it? Thanks!

So I took my belt off to adjust my water pump pulley and just so happened to grab the power steering pulley, the thing jiggles and even pulls out a bit (2 mm maybe). Also it is leaking fluid... This may solve my belt squeal and shredding probs as the fluid was on the belt traction area. Time...

I don't think I tightened my new balancer enough (stock replacement) as I shredded a belt the other day. I installed the balancer over 6 months ago, but ever since I installed it my belt has squeaked. I finally took off the $35 squeeky belt and installed a $15 dollar replacement that squeeeked...

I installed a new harmonic balancer a few months back. I don't remember if that is when it started, but maybe the pulley isn't lined up perfectly? The tensioner is still hard to pull down, so I don't think it is that. I have Mac UD pullies I installed over a year ago. WHy do my belts squeak?

I need to install this in about an hour, is it easy? DOes it replace the stocker or what? Walk me thru or give me tips please!

I have a chance to purchase an 04 Cobra drivetrain. We (dad and I) are currently restoring this 70 and should have it back from paint in 2 weeks or so. We have a BOSS 351 Motor and toploader waiting to go in but I recently saw a 65 fastback with a non SCed Cobra motor and became very...

Just want one right now. :D

I am pulling this code. Also, my TPS voltage is 1.04. How exactly do I adjust my TPS, hit it? Wiggle it?

The car idles smoothly when the spout is taken out, but when it is put in it surges and seems to miss. What is wrong here?

While crusing at 2K or 1500, the car just goes to 0 and back up VERY fast and several times in succession. Only happens once every 20 or so minutes. I have a new fuel pump. TPS is an AutoZone, about a year old. New IAC. What ould that be? Distributor is stock with 156 thousand miles.

Yuh.

Took my car to our mechanic to see if there were any vacuum leaks or anything causing my rough idle. He said that the car just ran really rich, and there were no codes for it. Is it time for an FPR?

K, my #1 injector was leaking on my way to my dad's car lot this morning. I ordered some new o-rings from Autozone and reinstalled it. BTW it was leaking where the injector and fuel rail meet. I put some WD40 on the o-ring and stuck it (the injector) back in. It "pops" in nicely, but falls...