Search results

I'm working on my AC system and I ordered a set of new o-ring seals for the car. All of them are green. I took the liquid line as well as the other line off the condenser and the o-rings were orange. Am I ok to use the green ones there or should I go get orange ones as well?

Normally I wouldn't even ask and just add the amount in the shop manual but when I took the plastic cap off to bolt on the AC hose manifold, there was already oil in there. I was trying to figure out if the compressor I bought came prefilled and the page says most assemblies are precharged with...

Hey guys, I have an 03 Mach 1. The AC quit working on me a while back. I could hear the compressor cycling on/off so I took it to a local shop for an AC diag since I don't have AC manifold gauges and what not. They told me I was low on refrigerant and did a die test. Said my compressor is...

Is there a stock type rubber bushing available for the upper control arms in the rear ? I know you can get a factory bushing for the axle side but I don't really want to pay 250 bux for a set of new control arms when I can just replace some rubber bushings for well under 100.

My dad's car is making too much power for his stock radiator. Do you guys know if the 03-04 Cobra radiator is the same as the GT radiator or if it is a bit beefier. His car isn't making more then a lightly upgraded Terminator so I figure if that radiator is good enough for a supercharged 4v...

Ok, so I put my new COP unit in and the car is finally feeling like it is almost back to normal. I feel like I am missing a little bit of power in the 4800+ RPM range. Down low feels just about right. You can see the TID results from Binary Editor that I have attached. I think the one at...

Last time I looked into it the aftermarket didn't really have a true upgrade for the factory COP units. All the aftermarket ones at the time were touted as upgrades but from what everyone said they were no better performance/reliability wise when compaired to the stock unit. I am seeing these...

Hey guys, I'm looking for a little help with my Mach 1. I've been having small issues with it that I've been hunting down. Every time I think I've got something fixed it eventually comes back. Until now the car has never thrown a code. Well, last night while I was driving, the car finally...

I'm in Utah at the Miller Motorsports park for my Boss Track Attack and they have a collection of extremely rare Ford cars and some rare assorted Ford parts. I came across this "Cross Boss" intake manifold and carb and I've never seen this before. You guys ever seen this ? Do you know if this...

I've been looking for a good 2 1/16" inch gauge that is both an oil pressure and oil temp gauge. I think the best one I've found so far is this OEM Porsche/VDO gague...

So I bought a Moats Quarterhorse for my 03 Mach 1 and installed it. No problems. I had the ECU out of the kick panel area and it was just hanging out. Everything was working fine. I put some electrical tape over the J3 port where the QH was poking out to seal it off so no moisture would get...

I'm looking to purchase a code reader/scanner and I'm looking for something I can use on not just my Mustang but all kinds of different cars. What do you guys think is the best all around unit that can do ODB2/CAN bus and maybe do ABS/Trans as well ?

Does anyone know if there are any aftermaket gauges that look like the Bullitt/Mach 1 gauge face ? I want to add some extra gauges to my setup because the stock ones don't give terribly usefull info. I'd like to add oil temp and a real oil pressure gauge. I was looking at the autometer dash...

Is there anyone out there that sells a prebuilt harness for a C4 to AOD swap ? I've rebuilt the stock and AOD harness together a few times for various projects but it seems like my friend I'm helping this time has managed to loose both. It would be easier to just buy a prebuilt one from a...

Does anyone know what the proper size for the u-joint is on the tilt steering wheel columns ? My friend's 68 has wicked play in the steering and we have narrowed it down to the u-joint. I was hoping to have the part in hand ready to go one once we get it all appart. I don't want to have to...

Does anyone know if the 03-04 Mach 1s had the same front swaybar as the 03-04 Cobras ?

I'm looking into replacing my clutch and I want to order a new one this month (mine doesn't have much life left). I spoke with Modern Driveline and they sugested a kevlar/kevlar clutch. They said it will be slightly harder pedal effort then stock with the pressure plate they sell and they said...

Is there a way to read the VSS output and convert it from a pulse to a constant voltage ? Alternatively, could I read the pulse that feeds the spedo gauge as a constant voltage instead of a pulse some how ?

What is the difference in ride height ? I'm swaping to an IRS and I'm thinking the Cobra is lower and I'll need to get the front springs as well.

I have been waiting to upgrade to a T56 and I finally have enough money to do it but over the last few days I've found some data about the gear ratios that I didn't know previously. I'm wondering if this is actually true or not. I have a 2003 Mach 1 with a 3650. I read that 5th gear in the...