Search results

  1. G

    Overheating situation need a Wise person

    Things to check From my heat problems I found the following: 1. Check for the plastic dam at the bottom of the radiator (can effect the idling temp) 2. You need to ensure that the space above and on the sides of the radiator are blocked like the stock setup which had rubberized flaps...
  2. G

    What plugs to use with KB?

    I now use Denso IK20 Iridium spark plugs, I tried IK22 but they were way too cold. I'm running a KB Blowzilla @8psi on 91 Octane with Edelbrock 60379 Heads, 2.01" intake, 1.6" exhaust valves, 60cc. Good Luck, Don
  3. G

    Best distributor and coil for 5.0?

    I've had good luck with Screamin' Demon coil and their 5.0 Dyna-Mod TFI module. Don http://www.performancedistributors.com/5.0ignition.htm
  4. G

    damn the low coolant light

    Usually cleaning the two prongs at the bottom of the sensor with get it working again. Don
  5. G

    Tire rubbing lower a-arm during sharp right turn

    Easy, loosen the boot clamp pull the boot back and slide the restrictor on the rack and pinion shaft. They look like a C clip. Don
  6. G

    Tire rubbing lower a-arm during sharp right turn

    You need these: Steering travel restrictors N804842-S Don
  7. G

    My Delta Current Control Question

    Just to add, fusible link wire has special insulation that won't catch on fire when the wire fuses. Don't use regular wire as a fusible link. FWIW, Don
  8. G

    please help pulled code 34

    D's 91 stang gt, When mine threw that code it ended up being the 10 pin connectors. Clean them real good and mate then unmate several times to get a good solid connection. BTW, mine was very intermittent and would only throw a code when cold. Don
  9. G

    Am i missing a nut?

    Actually it should be a solid flat nut and a pressed steel cap that is castle like features and fits over the nut. Don
  10. G

    Supercharger w/gears

    Roxy89, I'm running 275/40R17 Nitto DRs, Maximum Motorsports lower and FMS upper control arms, Transgo shift kit and 9.5" 2500 stall converter. You can't just floor it off the line on the street careful application is required. On a roll coming out of a corner it is awesome and you can get...
  11. G

    Supercharger w/gears

    "would the kenne bell really help? Also, w/kenne bell you really can't run too much of a gear, probably no more than stock or a 3.27, but w/the centrifugal you could run about a 3.73 gear (on a 5spd)." I run 3.73s with my 8psi KB and an AOD works great, and having 8psi anywhere in the RPM...
  12. G

    what is your fuel pressure set at/w 24lb inj !

    When I first put 24# injectors on mine 37# fp gave perfect Kamrfs with my Tweecer RT. YMMV, Don
  13. G

    Trans cable clip missing, Please help.

    Get one of these from Ford: http://www.sccoa.com/sccoo/Faq/tvcable.htm Don
  14. G

    FMS Oil Cooler Mounting!!

    Yes, I had to buy more hose because I had a tranny cooler where the provided hose would reach. I used Parker 293-12 5/8" hose because I couldn't find any of the Goodyear hose provided. Don
  15. G

    Please help with Charcoal Canister

    In my 90GT it is a black plastic line that runs along with the fuel lines along the passenger side frame rail then up into the passenger fender well and comes up over the shock tower and connects to the charcoal canister. This is a vent line for the fuel tank. Don
  16. G

    Crane 2030

    NKau, Yeah, no problem. Just wish the tires didn't spin so easy, well I've only got 275/40R17 Nitto 555R drag radials :-) That cam really pulls from 2K to 5.5K. Idle is slightly loopy but idles good at 672 RPM with lots of Tweecer tuning. Good Luck, Don
  17. G

    Crane 2030

    NKau, AOD, 2500 Stall 9.5" converter and 373s. I've ran it NA and now 8psi Boost with a KB Blowzilla. Never bogged in either case with a nice flat torque curve. It runs about 10" vacuum at idle (676 RPM) in drive and 12" vacuum in neutral at idle. Don
  18. G

    Crane 2030

    I run the 2030 with Edelbrock Heads with 2.02/1.6 valves and it works great on the street. I went with it because it has an EO # for CA emissions legal. You'll have to check the piston to valve clearance. Don
  19. G

    Confusing Day at the dyno...Need some qualified opinions

    Lambda = 1 =14.7:1 AFR Lambda = 0.8 = 11.76 AFR So Lambda X 14.7 = AFR Don
  20. G

    EFI experts; problem studdering acceleration... makes me wanna go carb

    A remote possibility is that the engine can get into a load condition that causes the HEGOs to report wrong information to the PCM. This causes bucking and or popping on mild to medium acceleration. I corrected this by lowering the open loop load limit vs ECT function in the PCM. This allows...