Search results

Guys whats a larger tires then the 245/45/17's that will look good on all four corners and fit the 8 inch wheel? Pics are helpful too. Thanks!

What can we replace a broken axle in a 86 turbocoupe rear with? Does anyone make the correct length axle or can we just use fox axles without the Anti-lock wheel?

OK guys, I'm at my wits end. The vehicle in question is 1997 Ford Explorer 5.0. It has fuel and has compression, but has no spark. I have replaced the Coils, Wires, Plugs, Computer, Crank sensor and Cam sensor. Am I missing something? I hate this car and just wish it would run again!

Just like the title guys. Where's the best place to get a set of GT40p headers? Shorty's by the way. Dustin

Ok guys this is really wierd. 1990 lx 5.0 5 spd. When the car has been sitting and is cold it will start and run fine for 5 to 6 miles, once warm the engine dies and will not restart. Once the car is cool again it will start and run fine again till warm. Engine is only about 500 miles old and...

Hey guys, I know whats required to install the 351w part of my swap but what about the c6 trans? What modifications are required. Everything is from an 1985 f150. Thanks for the help! Dustin

Well guys I pulled the wires out of the connector for the hazard switch when I was installing my new shift light. Does anyone have a good wiring diagram so I can sanp these back into the right spots? Thanks. Dustin

How many of you bracket race guys run consistent on nitrous? I'm having issue with the times going plus or minus half a tenth to a tenth. I don't have to tell you guys that a tenth matters in bracket racing. Anyone with ideas on how to tighten up the consistency please chime in. Thanks.:nice...

Well guys I'm about to grad with my Ph.D in Mechanical Engineering and with my emense Mustang background I was thinking about heading to Norman with my fiance and family and opening a Ford only performance shop. Are there any stangers on here that would try us out if I headed down? We would be...

Well guys I'm about to grad with my Ph.D in Mechanical Engineering and with my emense Mustang background I was thinking about heading to Norman with my fiance and family and opening a Ford only performance shop. Are there any stangers on here that would try us out if I headed down? We would be...

Hey guys my stock trans is grinding 3rd pretty badly. What aftermarket trans can I get that will be an easy bolt-up and hold alittle more power? :SNSign:

Anyone use the 1.7L non-intercooled kit from Kenne Bell? If so how about some pics? Was the install hard? Thanks.:SNSign:

Hey guys, Does anybody have the autometer gauge cluster? If so can I see some pics? Thanks!:SNSign:

Hey guys check out my notch in the classifieds. Its for sale or for trade I have to get my fiance a reliable car so the toy has to go.

How do I remove the rear speaker deck cover without damaging it? I want to re-upholester it. Thanks Dustin

What can I do to fix it? The sticky just talks about it and the TSB on it doesnt say it was a recall and the car is a 2001 Bullitt and way way outta warr. What are my options and the cost of each? It grinds 3rd only under hard throttle. Thanks guys!:SNSign:

*Ok there's no cookie but feel free to guess anyways. Winner will be known on Friday when I go to the track. Setup all new: 1979 Mercury Zephyr 2-door coupe 2730lbs. 306 eagle crank and rods Ford Racing b-cam Edelbrock RPM intake ported and polished Speed Demon 650 CFM Black Magic Fan...

When you installed your powertrax Lock-right what parts did you have to re-use? Do you reuse any of the clutch pacs behind the side gears? Thanks. Dustin

When you installed your powertrax Lock-right what parts did you have to re-use? Do you reuse any of the clutch pacs behind the side gears? Thanks. Dustin

Well we grenaded the trac-lok in the bullitt on saturday (upper and lower spider gears and side spider gears, one broke in half other stripped all the teeth off of. Side gears were in turn chewed up.) The axles and the ring and pinion are still good. I was wondering what you guy would recommend...