Search results

Alright, I am going to buy a new Air Temp. Sensor since I noticed when I did my ported lower swap, mine looked pretty crumbly...I also heard those CHEAP "Ebay 10hp+ mods" are just resistors that are spliced into the wires that go to the air temp. sensor on the lower intake. Any Electricains here...

I did a search, and understand that my 94 starter im using on my FOX, is considered a Mini Torque Starter...I know something about how to wire is from what I searched here, but I dont understang....something about a thin/thick wire setup? All I know is I need to remove the wire going from the...

I heard there is a different way to wire the 94 starter for a fox this way it wont drag...I know its dragging cuase something about reverse magnetics or something...dunno, but bascially the same thing happened when my friend bought a hi-torque mini starter, and he had to wire it differently to...

Is chattering normal? I have it everytime I begin to take off or in reverse too.... :shrug:

Alright, I took off my upper intake since my buddy is porting me and intake, and I figured it would be done by the completion of my transmission swap, it wasnt so I put it back on. Now my car wont idle right, and it shakes.... What could be the problem? Other than possibly a vacumm problem...

Alright, question, the Throwout bearing goes onto clutch fork, but wants to slide off, it will alright once the tranny is in since it will keep it in place right? Also, the position on the Throwout bearing is like as follows right? The small lip ring slips on the clutch fork(which it keeps...

Im putting a 94 cobra tranny in, with the newer bellhousing too, and the problem is...... My newer clutch fork has a weight on it...it looks like it can be taken off, but im not too sure when the purpose of the weight is. Do I need this on there, or just take it off? __________________

I just got my last piece, which is my bellhousing, but my Fork isnt long enough for the clutch cable...Will the 94-95 GT fork work with the 87-93 cable? Is so, I think thats all I need..just need to know.

Alright, she just came in about less than 5 minutes ago, so Ive got questions. The tranny wont be going in for a few days since Im still waiting on the newer Bell housing. Can I put the clutch kit in, and let it sit like that without the tranny on for a few days? Will it hurt anything? ALSO, I...

Alright, I just ordered my Ford Racing Flywheel(I got a CAT, but found out it was a POS..money lost there :bang: ) & my SPEC Stage II Clutch. How hard is it to install? This is how I figure it goes: Put the clutch onthe flywheel facing the right way towards the motor, then put the flexplate...

I finnaly pulled my tranny, and couldnt get the lid off to see how bad it was broken(and open the new one I got to see if its good). I know the lid is connected to the shifter shaft, so I tried splitting it open from the middle by removing the casing bolts. That did little, but It was enough to...

I was told this is a '94 Cobra WC T-5. I would like to know if someone can give me a link, or identify my newer tranny with the numbers below. Middle of Tranny(Driver Side): 13-52-065-921 Back of Tranny near Shifting Box(Driver Side): 13-52-066-939 THANKS IN ADVANCE! :banana:

Alright, I dunno...just worried. Before I get angry I dont know about these but its suppose to be a 157 Tooth 50 oz. Imbalance, Billet Steel Flywheel. It looks alright, but is there anyway for me to distinguish? I paid $150 Shipped from some guy and whats wierd the it doesnt look like what I...

Help please, ive been asking this question and need to know! I know you need the bellhousing but what else? will everything else from a fox work? I am buying a fox billet steel flywheel, a fox spec stage 2 clutch, and want to buy fox Cross member & tranny mounts. Will the fox stuff fit for the...

I am going to buy a 94 Cobra WC t-5 from a member here, and I need to know what do I need. Just the bell housing? From a 94-95 5.0 GT or what? Also I want to buy a billet flywheel and need to know if a 157 tooth 50 .oz imbalance will work for my fox & the 94 Cobra tranny? Let me know, ready to...

I cant find a link(So I need one if possible.) I found this tranny online SINCE MINE IS BLOWN. My car is just sitting by itself in the garage :nonono: Does this sound like a good deal on a tranny? Tranny I need this, and am ready to get it, just want some feedback. Lemme know, as always...

I Have a New Accel Super Coil (The Cylinder Shaped Ones) Can I install it on my Fox? I need info Quickly! Anyone know? Im guess I cut the stock TFI Clip off, and Instal the Green Wire to the positive and the Black to the ground side of this Coil. Anyone know if its possible or if it will work...

Well, I finnaly came around to contribute to this. I have field tested this install & relay for about 1 month, along with 89StangLX's setup I also did. Well, here you go, I hope this helps, Basically you just need wire connectors & Wire itself! :flag: 3.8L Taurus Fan Install -Nick :nice:

I get this wierd humming noise from the FRONT PASSENGER SIDE TIRES AREA...its loudest around 45MPH, and is worrying me. What could it be? Please help me...Im wanting my car to be safe, and not have something break while i drive on the highway..etc. THANKS! :flag:

My 89 GT Has posi, and works great, car is fully serviced, and I just want the basic kit install kit for pull-off 3.27 gears off a mach 1. Which kit would you suggest as a basic kit? Can anyone help? Who sells them? Help! :flag: -Nick