Search results

  1. glowstang93

    Let's see those Laser Red Mustangs!!!!

  2. glowstang93

    Tach needle dropping and jumping back up on '93 2.3L

    As I said before. Replace Icm and coil packs when tach jumps and runs down at 500. It will save u headaches later.
  3. glowstang93

    Electrical How do I get these rear turn signal bulbs out ???

    Amber NA
  4. glowstang93

    Trunk spring bumper 99-04

    Nice. Thank you.
  5. glowstang93

    Trunk spring bumper 99-04

    Best I can do is share the pic I got from 11/16 OD 3-16 ID 1/8 groove hardware store
  6. glowstang93

    Trunk spring bumper 99-04

    No sorry. Tbh best bet is to go to your local hardware store and look for it in the plastic boxes most have or big box stores just have to look for them.
  7. glowstang93

    Trunk spring bumper 99-04

    I replaced the trunk spring bumpers 1 year ago. Found one of the bottom rubber caps missing. Replaced them with thick grommets at substantially lower cost then new bumpers on my 2001 gt. Hope this helps someone out .
  8. glowstang93

    Electric fan fail

    The ccrm relay module controls the fan
  9. glowstang93

    93 Mustang LX - Integrated Relay Control Module replacement?

    I just recently replaced mine on my 93 due to fan and ac issues. Here is the link to what is inside. I got mine from O’Reillys. Ccrm. Control module. https://www.stangnet.com/mustang-forums/threads/constant-control-relay-module.899442/
  10. glowstang93

    Tranny fluid leaking

    Sorry I didn’t post back. Shop replaced front seal.
  11. glowstang93

    Improper storage caused serious issues (pictures)

    Keep moving forward it will be worth it. Mine sat for about 2 years. List of all it took to get it rolling again. Gas tank was replaced due to rusted out, all hoses, thermostat, coolant, radiator, relay control module, low pressure ac switch, tires, exhaust, hatch striker bolt, tranny seal...
  12. glowstang93

    Tranny fluid leaking

    Got back home just in time. Leaking tranny fluid bad out of the inspection plate on the oil pan. Any clues what could be the cause? 2.3
  13. glowstang93

    Valve cover torque

    I went with felpro blue rubber gasket. Hasn’t been on long but not leaking now.
  14. glowstang93

    Setting Base Idle

    Still works in 2021. Thank you old friends
  15. glowstang93

    Valve cover torque

    All set to remove cover. Going to wait for one of my sons to help line it all up. Hoping that EGR tube is going to be out of the way enough to position cover back in
  16. glowstang93

    Tach needle dropping and jumping back up on '93 2.3L

    Been there done that. Best to just replace coil packs and Icm same time. Glad ur rolling again.
  17. glowstang93

    Valve cover torque

    Thanks. Where did you find info. I’ve looked and searched everywhere.
  18. glowstang93

    Valve cover leaking

    Found some very similar m6 x1 12 mm flange bolts. Anyone have a torque setting for these? Googled and come up with 7-8 ft lbs but not much else.
  19. glowstang93

    Valve cover torque

    Anyone have the valve cover torque specs for 2.3. Googled and came up with nothing. Using the felpro rubber gasket.
  20. glowstang93

    Valve cover leaking

    Going with this one. I hope it’s a good one. Thanks for the info on the bolt.
Top Bottom
Back
Forums
Menu