Search results

Thank you again!

Thanks so much for the reply. That makes complete sense now. After reading your response I decided to go out to the garage and search all my boxes for the harness from the '91. I ended up finding it in the one box that wasn't labeled! From what I am gathering, I need to move wire in the top...

Great thread and great how to. Just have a couple questions that I still can't seem to get through my head. I am restoring a '91 notch that was originally an auto (now a T5). I put an A9L in it from a friend's '89GT I parted. Before finding this thread, I was going to use the O2 harness from...

What a great list. Maybe this is why I have had a draw somewhere in the #8 fuse on my car since 2002!

Thanks everyone. I installed the older Baer PBR front calipers (basically the same as the Cobra calipers but the spindles are set up for a 4 lug 12" rotor) and 93 Cobra master cylinder. I thought I could get away with leaving the booster but the pedal effort AND braking is terrible. Was going...

Thanks for the help. I was thinking I would need to take off my upper intake and unplug all the vacuum lines, etc. (luckily I don't have A/C!). Do you mean that you trimmed the studs on the interior side or the studs for the master cylinder (or both)? Also, do you know which hole(s) need to...

Great thread! Question: Can this project be done with the engine in the car AND without removing the master cylinder? I already have a 93 Cobra master cylinder and I was hoping to keep the lines connected to it.

Looks like he's been posting in other threads. I was a bit worried too.

The weather is supposed to be nice here this weekend so I am going to try to get some of my trim pieces done. When you are stripping the pieces, what are you using? Does it just need to be sanded and smoothed? I have various grits of sandpaper, a box of red scotch brite pads, a couple sanding...

Awesome, thanks so much! Sorry for the delay. Notifications were coming to an email that I don't check much anymore. I just updated it.

I would definitely be interested in seeing your method for the quarter windows. If you did a set for a coupe, I would be interested in buying them.

Awesome. Thanks so much! I forgot I also have the side mirrors too.

Hi Dave, I am getting ready to paint the trim on my car. Bodywork and paint was done by a shop, but I have to restore the quarter window molding and paint the following: front and rear windshield trim, plastic side molding trims (they did the urethane pieces), cowl cover, roof rails, and door...

Just finishing hooking up all the harness connections after reinstalling the dash on my 2003 GT. Need some help identifying where the two boxes circled in the picture go. The larger one slides onto the dash frame and the smaller one screws on. I remember taking them both off when the dash was...

The filter appeared to be correct. It was just so corroded that the nipple had a hole in it (causing a leak) and broke when I tried to remove it. The plastic pieces in the Mustang are much easier to work being with but I think the F-Series lines are a higher quality. I did put a little oil on...

Success on part 1!

Thanks so much for your help! Yes, it does have a bail clip like the ones shown. Am I correct in assuming from the article that I can just pull aggressively on the nipple of the filter that is stuck in the fitting to get it out? Or see if I can use a tiny screwdriver or file to break the bail...

Just got a beater F-250 mainly for plowing my driveway and driving to the dump. Noticed it was leaking gas at the filter. The fuel filter was corroded and the outlet port going to the engine snapped. When trying to remove it, that piece came off and stayed in the connector to the line. I...

This car has a lot of rust in a lot of areas that are more involved fixes. I have never seen an a-pillar rust like that on these cars. With that said, if you already have the right tools, it would be a great car to learn the skills if you are interested in body work. I would suggest not...

I've seen similar. Did you do any of the following: 1. Change the weather stripping? The new weather stripping that LMR sells is firmer when new than the original and made my door stick out. 2. Did the position of the door change when you replaced the pins? The door hinges bolt to a plate...