Search results

  1. Albrainya

    Intake Backfire

    set the base timing to 16 degrees and the intake backfire is gone and the car pulls like a raped ape, no pinging either.
  2. Albrainya

    Intake Backfire

    Heres my setup: 92 5.0 stock bottom end/rebuilt thumper heads (ported e7's) b-303 motorsport cam 1.7 roller rockers gear drive advanced 2 degrees (cam was degreed) efi spyder intake 24# injectors 76mm c&l mass air t-5 5 speed 8.8 rear with 4:10s I get a single backfire in the intake...
  3. Albrainya

    3 1/2 intake hose

    that hrpworld link looks like the ticket. comes in colors too. thanks for the info Dan
  4. Albrainya

    3 1/2 intake hose

    well, I wouldnt be caught dead in the rice section, so that leaves me with one choice. Thank you
  5. Albrainya

    3 1/2 intake hose

    hey guys im looking for some 3 1/2 inch flexible air intake hose i can use to plumb a custom intake setup from my mass air to the filter in the fender. I cant use any of the pre bent stuff, i need something flexible so i can route it the way i need to. Ive seen such setups on other cars but cant...
  6. Albrainya

    need wiring diagrams for fox body

    ck these links http://www.autozone.com/servlet/UiBroker?ForwardPage=/az/cds/en_us/0900823d/80/19/59/5a/0900823d8019595a.jsp http://www.autozone.com/servlet/UiBroker?ForwardPage=/az/cds/en_us/0900823d/80/16/71/3c/0900823d8016713c.jsp
  7. Albrainya

    5.0l/5.8l dimensions

    Question: are the outside dimensions of the 5.0l the same as a 351W? With shorty headers on a 5.0l, will shorty headers on a 351W exit in the same location? im wondering if i have to change my exhaust if i change to a 351W. Thanks.
  8. Albrainya

    Can someone ID a PCM for me please

    thanks guys
  9. Albrainya

    who makes fake blocks?

    theyre expensive, but its real funny to walk down the street with one holding it on your shoulder.
  10. Albrainya

    is this a good ground???

    I would run the ground cable (1GA) through the trunk floor and bolt it securely to one of the frame rails. then a ground strap from the engine block to the frame rail in the front.
  11. Albrainya

    Can someone ID a PCM for me please

    here are the numbers on the PCM F3ZF-12A650-DA A3M EEC-IV SFI-MA12A Thanks for any help I need to know what specific type of mustang this processor is from Dan
  12. Albrainya

    anyone build motors? i need to beat a honda.

    need to beat a honda? i have a radio shack electric motor about 1 inch long runs on a 9 volt battery that should be plenty to beat a honda. OR i have a new pair of tennis shoes that'll work too.
  13. Albrainya

    turbo coupe rear disc on a mustang rear

    what, the caliper brackets on a turbo coupe rear arent bolted on? they are welded to the housing? i thought they bolted on. anyway, the brake lines and master work arent a problem, i just wanted to know if the turbo coupe stuff would fit my housing.
  14. Albrainya

    turbo coupe rear disc on a mustang rear

    its not just powdercoated, it also has brand new 4:10s, with a motorsport posi unit, all brand new bearings, seals, etc.
  15. Albrainya

    turbo coupe rear disc on a mustang rear

    i know- i didnt mean to do that- i hit "post" and nothing happened. i waited for like 2 minutes then hit post again- nothing happened. waited for another 2 minutes then hit post again- then it went through immediately, like it usually does, then i noticed it registered three times- i tried to...
  16. Albrainya

    rear seat star shaped bolt

    Its called a TORX bolt. You need a TORX socket, i think its a T-45 or a T-50. You can buy a whole set of TORX sockets, youll need them on other parts of the car anyway Dan
  17. Albrainya

    turbo coupe rear disc on a mustang rear

    Hi- Has anyone tried to mount turbo coupe rear disc brakes (caliper bracket, etc) onto a mustang 8.8 rear? my problem is i have an 8.8 in my car that i had powder coated so i cant change the whole rear but want disc brakes in the rear, and dont want to spend the 800 for a conversion kit. I can...
  18. Albrainya

    turbo coupe rear disc on a mustang rear

    Hi- Has anyone tried to mount turbo coupe rear disc brakes (caliper bracket, etc) onto a mustang 8.8 rear? my problem is i have an 8.8 in my car that i had powder coated so i cant change the whole rear but want disc brakes in the rear, and dont want to spend the 800 for a conversion kit. I can...
  19. Albrainya

    turbo coupe rear disc on a mustang rear

    Hi- Has anyone tried to mount turbo coupe rear disc brakes (caliper bracket, etc) onto a mustang 8.8 rear? my problem is i have an 8.8 in my car that i had powder coated so i cant change the whole rear but want disc brakes in the rear, and dont want to spend the 800 for a conversion kit. I can...
  20. Albrainya

    Will cobra valve covers clear my roller rockers (edelbrock heads)?

    heres a picture of my engine- it has 1.6 rollers and cobra valve covers
Top Bottom
Back
Forums
Menu