Search results

Looking to get the 88GT done. I'm thinking I'll do the same as with the Mach 1. 8 point chromoly bar with outriggers and subframes through the floor. Two points for the harness to attach on the hoop crossbar. 2 of the points will be going to the upper torque boxes. Question I have is...

I'm looking to order up the ARP 3" long 1/2" x 20 thread studs but need to know what size knurl on a stock front end?

Derale 16928 - Derale Rad Dual Electric Fans Derale 16928 - Derale Rad Dual Electric Fans-Overview - SummitRacing.com Edelbrock 8843 - Edelbrock Victor Series Mechanical Water Pumps Edelbrock 8843 - Edelbrock Victor Series Mechanical Water Pumps-Overview - SummitRacing.com March...

Hi all, Car currently has the stock setup with A/C. So it goes Crank, W/P, P/S, A/C, tensioner, Alt, and then Smog. I am installing a manual steering rack, removing the A/C, and the smog. So all that will be left is the Crank, W/P, tensioner, and Alt. How should I go about...

So I'll be getting the FRPP wires....but which ones? The 8mm or 9mm? Engine is stock for now but will me making good power later on down the road. What defines the need for thicker wires? Thanks, Mike

Stock vs BBK chrome unequal shorty headers, BBK o/r H-pipe, and Mac Produmps. YouTube - 1988 Ford Mustang GT stock exhaust vs modified

Welp...I was removing the stock headers and snapped two bolts on the passenger side. :nonono: How do I go about removing the studs stuck in the head? Thanks, Mike

I'll be installing my headers in tonight. So....just make sure the engine is stone cold? How about torquing the headers down. They're the BBK so it's a plate to the header surface. Do I go from the inside out? Also how much torque? Thanks, Mike

Hey all, Looking to get a custom cage on the Stang. I'm thinking a 10 point but was wondering how the dashboard setup would go. Anyone have pics or comments on the dashboard setup? Like I know the tweets will need to be removed and the cover modified. Is there a dash mod needed...

Hey all, Is there a write up on how to set up the fox GT car to allow for the parking lights and fog light to be all that's is on. Basically leaving the headlights off.

Hey all, I installed the MM kit. The quadrant, firewall adj, and their recommended universal stock cable. It's smooth as butta now but the only problem is that the clutch catches at the very top. I'd like it to catch in the middle. I have the firewall adjusted all the way in and...

I just picked up a 93 coupe with a 302, holly intake and heads, and a crane cam. It's got 42lb injector's in it with a Pro-M MAF. The guy was getting ready to put a D-1 in it but never got around to it. The car hasn't been put together enough to run so I don't know if it'll run fine...

Hey guys, I tried searching for it but I can't find what I'm looking for. My TKO-600 came with a rubber plug for the mechanical speed sensor. Well since I'm using the electrical connection. I need to get rid of the rubber plug and replace it with a plug I saw before. I can't remember...

Hey guys. I tried the search but couldn't find what I was looking for. I have the stock tranny out of my 04 Mach 1. Now I'm about to install the Fidanza flywheel and clutch stuff and Lakewood bellhousing. Now when I bolt the tranny up. Will the stock tranny mount/ crossmember work? Or...

I'm planning on getting the HPM Megabite Jr. lower control arms for the '04 Mach 1. What uppers should I get? I don't need adjustables as I don't plan on adjusting them. This is for drag racing on a weekend driven car...not road racing. Thanks, Mike

Looks like a four seater to me.... :shrug: