Search results

  1. V

    T5 Swap

    T45 is crap, won't work.. U can get a t5z, $1500, but they'll break just the same. Save up for a tremec and lighten up on the throttle until then
  2. V

    Drivetrain Throwout Bearing Issues

    If you just answered yes to the bearing noise going away with partial pedal effort, then it's not a bad bearing. The throwout bearing needs pre load, in other words it needs to have constant pressure against the flywheel. If the adjustment gets too loose then the bearing will squeak and...
  3. V

    Drivetrain Throwout Bearing Issues

    Does the noise go away if you put slight pressure on the clutch pedal?
  4. V

    66 Rearend Swap

    I did have to weld on new perches. I didn't narrow mine, I used sn95 mustang wheels and it worked perfect
  5. V

    94 Z28 Vs 93 Notch

    I took it to mean a posi traction unit in the rear end. Good question
  6. V

    94 Z28 Vs 93 Notch

    You're wrong shoomakan, a 94 z28 is only putting out 260 HP, his fox with gt40 heads will be 40-50 HP more than the z28 Don't forget, the camaros didn't get ls1 engines till 98
  7. V

    Modern Maverick

    There are many Efi harnesses out there, rjm is one. You are going to have big header issues running those gtp heads in a maverick. I suggest you go to maverick.to forums and see how others made out work. That intake is perfect for those heads, and the throttle body too, it's a 65mm.. The...
  8. V

    66 Rearend Swap

    Explorer 8.8... Strength of a 9", at under $200
  9. V

    65 Fastback Correct Wheel Offset? Torq Thrust

    17x7 4" bs for the front and rear or you can run a 17x8 I think 4.5 bs for the rear. 17x8s too wide for the front really.. I got some in with 245/45 up front, but have trimmed fenders
  10. V

    Drivetrain Throwout Bearing Issues

    Gap between flywheel and clutch? That's a first, I certainly hope there is no gap, a clutch must be tightly clamped against the flywheel to operate. What symptoms is the throw out bearing giving you to tell you it's failed? Often people replace the bearing when it's just a bad clutch...
  11. V

    Trans Questions.......

    It'll need a new second gear, rebuild kit, and likely a 1/2 slider
  12. V

    Drivetrain Clutch Noise?

    If it goes away with only partial pedal pressure then your church adjustment isn't tight enough
  13. V

    94 Z28 Vs 93 Notch

    Also to the above poster, 5.0 5 speed cars were rated 14.3 in the quarter off the lot, it was the aod cars pushing 15/16 seconds
  14. V

    94 Z28 Vs 93 Notch

    You've got the right mods for a high 12 second car on sticky tires. You should be putting out 300 at the flywheel give or take.. He's just got an old lt1 350 SBC in a heavier body.. You should be able to take him no problem
  15. V

    Distributor

    Yea, machined surface, looks steel
  16. V

    Distributor

    Roller cam needs a steel gear.. Drive the pin outta your current dizzy, press the old iron gear off, and press on a steel one
  17. V

    Fuel Lines

    Go to autozone, they have efi lines... It's flexible soft line sold by the foot, but designed for efi pressures.... Cut to length use efi clamps, itll work perfect
  18. V

    Oil Pressure Dropping To 0 Under 1500rpm-???

    faulty stock gauge? Gotta install a real gauge and go from there
  19. V

    Can't Get Interior Lights To Turn Off!

    sounds lame, but recheck the door switches..unplug em see what happens
  20. V

    Stock Fuel Pump

    that stock 88 lph pump is killing you...it's enough for gt40 heads, but certainly not your heads. You're probably going way lean up top ...Just stick in a 255...what the engine doesn't use, it'll simply return to the tank. Those 24's probably aren't big enough either. With ported heads...