Search results

I have DTC code P0463 and P2068 coming up. They are Fule Level sensor circuit high input and Fuel Level sensor B circuit high. I just had Ford replace my battery 2 days ago. Anyone know what would cause these errors?

My Zex kit is not spraying correctly. While troubleshooting the issue I had a friend rev the car to 5k and the Nitrous did not engage nor did any fuel spray. The Window switch is set to engage at 3k. After a few seconds of running the car at idle it started to spray both fuel and NO. It should...

I plan on getting some aftermarket wheels (A.Z.A. Z-2) with the following backspacing (F 18x8.5 - 5x114.3 - 35 - HL R 18x9.5 - 5x114.3 - 45 - HL). What backspacing is recommended for this wheel size? I have searched other threads and could not find my answer. I want the rear wheel to have a...

What gives!!! My 1st set of rear rotors/pads went metal to metal at the track... The fronts were still ok (worn, but good). Next I upgraded to powerslot rotors in the back and then the passenger side rear broken, it split completely through both sides of the rotor! THis happened after only 5k...

What is involved with taking the Shaker100 system out of the dash? Are any special tools needed? Does anyone have a wiring diagram for the car? I need to tap into a wire that is hot when the car is on. I plan to wire my radar detector in.

I lost a wheel cap racing this weekend, and cannot find a replacement. Where can I get a replacement cap for this wheel.

Is there really a 10+ HP improvement with these throttle bodies? What is the best brand to go with? What size?

I have a vibration that will not go away. It gets worse the faster I go, but is not relative to RPM. In any gear at 45 it is not that noticable at 75 it gets worse and at 100 it gets even worse. To try and resolve my problem I have replaced teh following: new gears(3:55) with new bearings...

I have a vibration in my seat in the mornings and after work when the car is cold... What are the possible causes. I just replaced the trans mount, u-joints, tailshaft bushing and yoke. The rear end is a used replacement peice that has been in the car for a few months. The driveshaft has about...

I am looking at getting these off of ebay? will they work? 17x8.5 I beleive? Not sure on the backspacing...

I purchase a OEM yoke from 50resto and the Ujoint that I purchased from Oreilly's will not fit in the yoke. The holes in the yoke are to small... Are there different Ujoints? If so How will it fit into the driveshaft... This sucks!!!!

I have a Ujoint that is connecting my yoke that will not come off. I have the yoke off but I need to remove the ujoint from the driveshaft. I tried brut force and knocking the holy crap out of it, but I dont want to damage the Dshaft. Any tricks anyone knows of?

What are the torque specs for the bolts that bolt the Throwout bearing retainer to the trans?

What grease should I use if I need to it grease up? Do I need to grease the throwout bearing and fork too? New at all this trans and clutch stuff...

The seal is above the oil pan so do I have to drain the oil to replace it...

I didn't pay attention when I removed my throw out bearing. How is it suppose to go on. Any pics?

I am replacing my tailshaft bushing and I started to take the tailshaft off and noticed gears and things inside. It did not want to loosen up as easily as I expected so i put it back together, plus all the gears and such scared me off. Is this something the Trans shop should take care of or can...

Lately my car has not been starting. I have power but when I go to start it evrery other time I dont even get a click. If I keep at it it eventually starts. Sometimes it takes 2-5 times other times it takes 10-20 times. I believe its the starter. Your thoughts please.

What is involved in taking the rear end flange off? I have taken the flange bolt off but how do I remove the flange from the rear end? Please dont tell me I need to take the diff cover off...

I feel air coming out where the exhaust tubes connect to the X pipe Cats. I have the clamps on really tight but air is still escaping. Do I just need to install it again and shove the xpipe futher up to the header pipes or is a little air OK? Will this hurt performance?