Search results

  1. jnobles06

    4r70w Shift Selector Arm On Trans Question W/pic

    Ok. So, I just installed the new engine in the marauder (4R70W same as the 03 mach 1 auto) and got the tranny all bolted in. When I went to hook up the shifter arm to the cable it wouldn't reach. I came to the conclusion that it got spun around when it was out of the car. Now that it is in the...
  2. jnobles06

    brake light switch

    i converted to a manual transmission in my 95' and cannot figure out how in the hell the brake light switch mounts to the pedal assembly or what parts are needed. i have the little switch that plugs into the wiring harness and when i squeeze it it works but i think there may be something im...
  3. jnobles06

    Cobra IRS

    my buddy will he has a 03 irs in his gt and wants to swap back where are you located. hes in clovis nm.
  4. jnobles06

    Vortech T-trim

    well i guess i need to build the motor then and up the boost :)
  5. jnobles06

    Vortech T-trim

    since the t-trim is a bigger supercharger than the s-trim does it lag more? for some reason my t-trim isnt making full boost untik about 5k.
  6. jnobles06

    bassani mids vs flowtech longtubes

    ya i noticed that the flowtech's were around 450 bucks and the bassani is like 650 but traditionally arent longtubes the best as far as headers go. im sure i would take his exhaust plus some cash. plus do longtube have problems scraping the ground on newer mustangs?
  7. jnobles06

    bassani mids vs flowtech longtubes

    i have a blown 00' gt with bassani mids with 3" all the way back but i have an automatic and the headers vibrate since they were not intended for autos (previous owners mistake). i have a chance to trade a friend of mine for flowtech longtubes. which one is better? summit states that they will...
  8. jnobles06

    Sputtering and Stumbling under accel

    my spark plugs are black with carbon i believe that they are the problem because they dont burn the fuel efficiently enough for the high compression that i have and maybe i need a copper race plug that is more suited for my application. so i do have a reason for blaming them. any suggestions?
  9. jnobles06

    Sputtering and Stumbling under accel

    my carb is squirting with the car off when i move the throttle very little. the reason i called the autolite crap is because im supposed to be using accel 276 because i have world products windsor sr heads my compression is 10.5:1 i think they have a longer reach and they are tapered. i just...
  10. jnobles06

    Sputtering and Stumbling under accel

    well i pulled out my spark plugs and they were black i think im running to rich or something i checked the float level on the carb and it was ok do you think it could be the spark gap or the crappy autolite plugs i was running?
  11. jnobles06

    Sputtering and Stumbling under accel

    ok i advanced the timing from 6 to 12 degrees with the timing light and checked the carb to see if it was squirting and it was good then i gave it a little gas and it stumbled then the idle increased to 1600 from about 1000 rpms.
  12. jnobles06

    Sputtering and Stumbling under accel

    i know this is a classic tech but i have a 95 mustang with a 74 351w that is fully built and stroked with h/c/i. i am running a holley 750 with a summit electric fuel pump and a holley reg. @ 7psi w/ full msd ignition. the car was just taken for its first drive and as soon as i give it a little...
  13. jnobles06

    96' Clutch pedal assembly

    will a clutch pedal assembly out if a 96-98 work on a 95?
  14. jnobles06

    crossmember question

    its a fox bellhousing. i guess ill find out if everything lines up when i install it.
  15. jnobles06

    crossmember question

    im converting my auto to a t-5. the t-5 is out of a 1993 5.0. i have the right driveshft and the spacer for the driveshaft to make up for the length difference but, will a 1993 crossmember work on a 1995?
  16. jnobles06

    how to run straight up carb?

    what all wiring is needed, ex how does the ingnition work and what all kinds of stuff like that do in need? should i get like a msd 6al, msd coil, and dist? what does the electronic choke on a carb hook up to and will all my blinkers, and lights work with out the computer and stuff? would my...
  17. jnobles06

    how to run straight up carb?

    i have a 95 v6 that was converted to a 351w carb. the wiring in it is all f@#! up and i want to rip everything out and rewire it carb with no computer how do i accomplish that? what do i need? any info will help. thanks.
  18. jnobles06

    shortblock question.

    well every thing is bran new and the machine shop that i had file the rings did the rings for street/strip applications i was thinking somewhere in the 30-40 range.
  19. jnobles06

    shortblock question.

    how many ft lbs should it take to rotate a shortblock? thanks.
  20. jnobles06

    95' engine/computer harness removal?

    i have a 95 v6 with a carbed 351w. im going efi so im removing the v6 computer harness and computer and replacing them with a 95' gt's computer harness and computer. i pretty much have the harness pulled out but i cant get it all the way out. i think the hole is big enough in the firewall but...
Top Bottom
Back
Forums
Menu