I have a Hurst Billet Plus shifter on my 89 GT. The stock knob fits fine. I'd like to swap the knob out for an OEM Mach I/Bullitt knob. Will this work? If not, anyone know of a repro Mach I/Bullitt knob that will fit it?
I will admit I got a supposedly OEM Mach I/Bullitt knob off eBay. The...
Anyone have the part number(s) and a good source for front and rear Spicer u-joints to fit a manual trans 1989 Mustang GT? Is front and rear the same part ( don't think so but thought I'd check).
Thanks,
Mike
I keep getting a Code 29 in continuous memory on my 89 GT with a T5 and the A9P computer. VSS is relatively new and the cruise works fine and no stalling at stops. What gives?
My car feels like a weak cylinder with a mid range mild shudder during acceleration and was trying to get to a...
Anyone swap in an A9P computer for a A9L? If so, did you get pinging in the mid-range under acceleration?
Stock 89 GT with T5 trans....I know the A9P pulls in +10 deg timing in midrange rpm and +1/2 deg at WOT over the A9L. I have a minor mid-range rattle that seems to lessen when I use...
I got a washer bottle off eBay that doesn't have the low level sensor nor the hole for it.....can I simply pull the one off my old one, cut a hole in the eBay bottle and fit in the sensor?
Thanks,
Mike
I haven't actually run the window motor yet but they seem to fit and should work. You will need to reshape the end a little with a needle file. Be careful as the brush is soft compared to the file. :nice:
I'll be installing the motor with new brushes this weekend and will only post if I...
Check this out!
MOTORCRAFT® WIRING PIGTAIL KITS FOR FORD, LINCOLN OR MERCURY VEHICLES
If you click on the links on the upper right of this site, you can download two pdfs of Ford connector IDs!
Might help out some day! :nice:
Enjoy!
Mike
I may need to change out the fuel pump in my stock 89 GT, I have a very intermittent fuel pressure drop. :mad:
I'm on my third or fourth pump over the 13 years or so I've owned it due to various problems. What's in it now is a stock replacement from Car Quest that replaced the entire...
On eBay, there are some roof rails that are listed for "sedans only".....would these also fit hatchbacks? Is there a difference between them? I would think not.
I asked them and they don't have a clue....just said whatever the listing says is what it fits......
Anyway, these rails are...
Will the red-button later model (early to mid 90s) inertia switch fit into my 89 GT that currently has the white-button model?
I'm thinking my inertia switch is causing an intermittent fuel pump shut off......you guys think the switch can do that? I've changed everything else....fuel pump...
Anyone know where the fuel pump ground actually is? I'm assuming it goes to a ring terminal with a sheet metal screw somehwere under the car?
Thanks!
Mike
I MAY have a problem with my A9L in my stock 89 GT and I know the A9S is California.....if I had a line on an A9S and swapped, would I be able to tell the difference?
From a tech standpoint, exactly what is different between the two? Spark tables?
My Stang stalls when it gets over 100 out. It stalls when I come to a stop then usually can be restarted. Sometimes it has to cool down for 10-15 minutes then will start like nothing happened.
Another thing is when hot out it will occasionally drop from a cruise of 75mph and die out to 60...
Kommiefornia Smog Links...See How Bad It Is Here
--------------------------------------------------------------------------------
Here is an official link on the remote sensing:
http://www.arb.ca.gov/msprog/smogcheck/smogcheck.htm
Here is a link where you can rat out your neighbor...
I want to install some poly rack bushings....Is there enough slack to just unbolt the rack from the frame with it up in the air and swap them or do I need to drop the outter tie rods and unhook the steering shaft (and hoses)?
I'm wanting to rebuild my speedo but I have searched everywhere for a good tech write up. Can anyone point me to one?
I found this site to get some of the internal gears.... http://www.odometergears.com/
I think my magnets are getting weak as the needle bounces a lot past 75 (stock 86...