Search results

  1. D

    11.0 AFR @ 30psi on dyno

    Ok thanks for the info on running the codes but it confirmed something that im not too happy about. KOEO i got 1,65,66,85,95,96. KOER i got 21,44,33,94. With the cylinder test the first time i got a 9, second time i got 8,6,2 and the third time i got 6,5,4,3,2.....pretty odd. 66 is MAF voltage...
  2. D

    11.0 AFR @ 30psi on dyno

    Timing is at 12 degrees advance w/ jumper pulled.
  3. D

    Questions on My MAF Upgrade. Fuel Relay, and Other stuff....

    One thing that i argued with a guy at C&L over the phone was fan wash. He said if you run a cone filter right in the bay it will catch air from the fan and surge your idle. It personally never happened to me but...if all else fails check it.
  4. D

    11.0 AFR @ 30psi on dyno

    306- dart pro 1 heads, cobra intakes, 24# injectors, C&l MAF, A9L. Ok I used to run Mid 12's with this setup until i take her for a trip home for thanksgiving. A 4 hour drive went well until i got here and the car runs but is very lacking in power. So i take it to the dyno for a tune and they...
  5. D

    Amp problems

    Ok i was driving down the road listening to music and my lights started dimming down, after which my bass cut out. My amp has done this before but i usually turn it down and it comes back on after a bit. Well this time she is not happy, its blowing the first fuse (60 amp) off the power wire from...
  6. D

    boost/overheating problems

    Ok solved the overheating problem today, my brand friggen new thermostat malfunctioned....woulda been easy to see my hoses balooning up if i wasnt so frustrated about the boost problems. Any ideas about the boost problem are still welcome.
  7. D

    boost/overheating problems

    Well i finally got my headgaskets replaced, and i went along and got all new gaskets/bolts for everything and she ran good with no boost just really rich. I compression checked her earlier today and all cylinders were around 120-140 psi, not bad. I broke her in about 1500 miles or so, and...
  8. D

    Pro 5.0 short throw shifter

    Thanks for the info
  9. D

    Pro 5.0 short throw shifter

    Alright i met a guy selling a pro 5.0 shifter for 50 bucks or so, but it was in use on his stock 5 speed stang. Is this shifter interchangeable with my tremec or are they not?
  10. D

    vacuum line routing

    bump
  11. D

    vacuum line routing

    Ok just took off smog pump and A/C, and was wondering the exact way i should reroute these vacuum lines. i have 2 big lines running from the upper intakes 2 sided larger tree, one to the pcv valve the other to the tree mounted on the drivers side fire wall. Ive got 1 red line from FPR to the...
  12. D

    anyone else have this problem??

    Im having a little problem with the rear passenger side bolt on the AC compressor. Ive got it backed out as far as possible but its hitting the head and its not far enough out to pull the compressor out yet. Im taking it off to pull replace the head gaskets, and its definately not going back on...
  13. D

    electrical problem

    Well i believe i have found the problem yet my rear right blinker still doesnt work. The autoparts store gave me the hazard flasher for the blinkers and the blinker flasher for the hazards....I didnt think they would make that big of a difference but i swapped them out anyways and everything...
  14. D

    electrical problem

    Can someone please get me some wiring diagrams that i can read a little better than the haynes manuals?
  15. D

    electrical problem

    A few days ago my blinkers and my hazards were acting up, the hazards stopped working completely and the right side blinker would just stay on and not flash when clicked to that side. Now neither of my blinkers work period, whats even stranger is that when i went to replace the flasher in the...
  16. D

    Used Gt40 "X" heads

    Ive been calling around and have found some used GT40 "X" heads here in san antonio and ive got some questions about them. For one thing they are 150 bux a piece...they are supposedly rebuild, but they sound a little too cheap. They will also port/polish and do a 3 angle valve job for 150 each...
  17. D

    need some help badly

    Ok i finally got my car fixed, seems like i blew a small piece of my upper intake manifold gasket, and a 2 inch vacuum hose that connects to back of the intake manifold. Anyways im contemplating slapping the charger back on it but i would hate for the same **** to happen. They said that the...
  18. D

    Wiring problem

    After killing the car the T-rex and the in tank fuel pumps would still be running with the car off. So i check all the wiring and the previous owner did some sort of weird wiring job on it . He had power to the t-rex running off of the power wire to the in tank, but he had a wire running to the...
  19. D

    need some help badly

    Is there any reason why pins B and C on my MAF are showing infinite resistance...i checked them all and everything seems good on the sensor besides these two pins and the haynes manual has nothing of that sort to double check with. Also after tinkering with leaving the battery off for around 30...
  20. D

    need some help badly

    Ok i ran the codes in koeo mode so far and i got 11 first, then i kept getting 66 saying the MAF sensor was screwed up. So i pulled it off and used intake cleaner on everything and plugged it back on and it still didnt work. But after killing the car the damn T-rex fuel pump is still running...