Search results

  1. S

    MAC Products

    I have been waiting 3 months for my 1 3/4, 3in primary, ceramic MAC headers. I was told i would not be charged until they were sent out however i was charged for them the day after my order. I was originally told they would take a week, then was told a few weeks later they were being coated, and...
  2. S

    MAC Products

    I have been waiting 3 months for my 1 3/4, 3in primary, ceramic MAC headers. I was told i would not be charged until they were sent out however i was charged for them the day after my order. I was originally told they would take a week, then was told a few weeks later they were being coated, and...
  3. S

    Trickflow heads and 1.7 Rockers ?

    Anyone, Anyone...Please
  4. S

    Trickflow heads and 1.7 Rockers ?

    Those that have Trickflow Twisted Wedge heads with 1.7 Rockers and a Trick Flow Stage 1 cam on a stock short block, what pushrod length did you end up using ? Please let me know, Thanks
  5. S

    Blue Oval Performance?

    Does anyone know Blue Oval Performance's Exchange Policy?
  6. S

    Crane Springs and 1.7 Rockers

    Anyone? Anyone?......Please
  7. S

    Crane Springs and 1.7 Rockers

    I just installed a Crane spring, retainer, and lock set #44308 on my GT40 heads with a TFS cam and Crane/Cobra 1.7 Rockers. When everything was installed and the rockers were torqued down i checked the clearance between the rockers and the retainers and nothing seemed to be contacting, however i...
  8. S

    Trick Flow Stage 1 in a Cobra?

    I wasn't planning on using 1.6s. Im curious why you think it would be better to use 1.6s?
  9. S

    Trick Flow Stage 1 in a Cobra?

    Did you have to use any shims? Also what kind of horsepower are you putting down with your setup? Thanks for the help.
  10. S

    Trick Flow Stage 1 in a Cobra?

    Anyone here with a Trick Flow Stage 1 in a Cobra or GT with stock heads, if you do, what size pushrods did you have to use and did you need shims to get the rocker adjustment correct? Please let me know, Thanks.
  11. S

    Slipping or Riding the Clutch?

    In regard to launching techniques i keep reading about riding or slipping the clutch when you launch. How exactly is this done? Thanks for the help.
  12. S

    Taking the Cobra to the Dragstrip..Any Advice?

    Well im going racing on Friday night and this is my first time drag racing my mustang. Ive done some drag racing before although it was in an automatic. Do you guys have any tips on burnouts (manual trans car), launching, and shift points? I also may borrow a friends drag radials to use. BTW...
  13. S

    Exhaust Popping with New X-Pipe?

    Yup thats me, you had the red 95 right? I think the next cruise is in Febuary, although im not sure where its going to be held. Ill see you at the next one...
  14. S

    Exhaust Popping with New X-Pipe?

    Yes, it sounds similar to a backfire, however it is not a loud shotgun sounding type of backfire.
  15. S

    Exhaust Popping with New X-Pipe?

    I just installed my offroad X-pipe today and after i took it for a drive i noticed a lot of popping sounds comming from the exhaust on hard deceleration. The only thing that i can think of that caused this is leaving the metal tube comming from the smog pump open and just hanging next to the...
  16. S

    Problems with Exhaust Alignment?

    I installed me new X-pipe (UPR) today it and went together pretty well, however one of my tail pipes (right side) hangs a bit lower than the other (the left tail pipe tip is touching the top of the bumper but the right one hangs 1/2" lower and does not touch the bumper.) Also i am using a...
  17. S

    VibrantRedGt and everyone else: Funny Pic

    Someone brought a "post a pic of your car" thread back from the dead (2003) on corral.