Search results

  1. S

    Car fixed, Distributor to blame! GRRR, YAY!

    After hours of searching, I found this post, pulled my distributor and had the same problem. new distributor later and it feels like a different car!! Thanks!
  2. S

    Just bought a 95GT and found some suprises

    I am going to keep the stock 92 cam with some 1.7's. With the 4.10's it should feel real good down low, which I want.
  3. S

    Just bought a 95GT and found some suprises

    Hey guys, I just picked up my first SN95, a green 95GT. It has a clean title and 101k miles. Mods are 4.10's, bassani cat x pipe, flowmasters, headers, and a pro50. I traded my 88LX convertible that had a salvage title and I repaired it. It looked great, and had basicaly the same mods...
  4. S

    Timing backing down on its own

    Thank God for Corral, 10 replies over there...
  5. S

    Timing backing down on its own

    I recently got my Trickflow H/C/I all together, and am very happy with it. I have a problem with the timing backing down. I set it at 20* spout out initially, and after a day of driving the car, I checked the timing because it seemed a little sluggish. Sure enough, the timing had dropped to 8*...
  6. S

    idle and code help please

    I looped the wiring that goes to the pedals(the sensors are missing) and it doesnt do anything weird when I put it in gear. now the only problem is still a code 67, CEL is still on and it wont KOER code read. Is it OK to just leave the pedals like that? Do you still think there is a wiring...
  7. S

    idle and code help please

    IAC is very clean. I know what the code is, there is NO ac on the car, and the car is in neutral when I run the test. Also why would it cut out when I put it in any gear?
  8. S

    idle and code help please

    I bought a bare shell EX-CHP for $200 and decided to put the car back together. It has TFS heads, Stage 2 TFS cam, and a TFS track heat intake on a stock Shortblock. The check engine light is on, and will come on about 10 seconds after I start the car....but when I start the car, it revvs to...
  9. S

    Replacing inner fender apron

    Ttt
  10. S

    Replacing inner fender apron

    I already drilled out all the spot welds and removed the inner fender apron, does anyone sell them new or do I need to go get a used one? Thanks
  11. S

    The thread of the nicest FOXES!

  12. S

    Any idea why these would be inside an 8.8?

    A friend of mine just bought an 8.8 with 3.73's that needed a new bearing installed in it. While taking it apart I found 4 of those metal tabs inside. Never seen this before, does anyone have any ideas?? Should I just go ahead and do the bearing, put it in the car and see how works? Thanks!
  13. S

    Inline Fuel Pump install (GSL392)

    Well I found out its the pink wire in the fuel pump harness. I have everything figured out except for hooking the pump into the factory lines. Do I need the fitting I mentioned in my first post?
  14. S

    Inline Fuel Pump install (GSL392)

    I just bought a GSL392 and am trying to figure out how to get it ann hooked up. I used this but I am still a little unclear: What color is the wire that I need to tap into that powers the intank pump? I went to Ronmorris.com and found what I think I need, a 90 Degree Duckbill Fitting...
  15. S

    Quick question about tremec TKO alum bellhousing

    You use the T5 plate and stud
  16. S

    Headgasket or rings???

    This is the first time I have checked the compression on this motor...
  17. S

    Quick question about tremec TKO alum bellhousing

    all it comes with is the bolts to connect the bell housing to the tranny.
  18. S

    power steering or not ...hows manual steering ?

    My friends 91 coupe has a flaming river manual rack and it is pretty easy...not nearly as easy as power steering though. Its pretty much the middle between power steering and a power steering car without a pump...
  19. S

    Headgasket or rings???

    I dont think 13# is "over-boosting". Also, I dont think was any detonation. The plugs all looked the same today when I pulled them out. There is not oil in the water, and no water in the oil. The first 800 miles it didnt do this, now it does. It pretty much started when I put the heads back on...
  20. S

    Headgasket or rings???

    My car recently developed a problem after about 1,000 miles. I had my heads off to get resurfaced and new valve springs, and when I re installed them I reused my MLS head gaskets for the first time. The problem is that there is smoke coming out of the valve cover, just a puff every couple...
Top Bottom
Back
Forums
Menu