Search results

reply 6al has a soft touch rev control thats all i know

reply did you run the red wire from the computer to under the drivers seats where the fuel rely is that clear up my idle. but they say it will have a little bit of a rough idle when you change over to mass air. are you runing the stock air box to the mass air or do you just have then filter off...

could a bad plugs cause an idle issue i have a bad loop when cold idles at 1500 rpms then drops to 500 then idles at 1500 then drops i check the plugs and the gap is at .060 if not more. i already check vacuum hose,change iac, but now its pissing me off i pulled codes but nothing should i do a...

im looking for someone who knows who reprograms computer or if i should get a chip. right now my car runs like ass cause my computer doesnt know what to do i put my hyperchip in it and it makes it worse. is there any one around chicago ill that does this its for a 86 switch over to maf and how...

i been having this problem where my car wont stay running when its cold and it smells like raw fuel and a bad idle i tried to advance my timing but its the same i touch the top of the msd rotor where the plugs go into and got shock not once but twice could i have a bad plug wire there are 9 mm...

ok i got this computer off of ebay its suppose to be from a 50 5 speed the cars been having cold idle problems and its getting worse so i ran a tester through it and it gave me code 67 which is neutral gear out for an auto but why would it throw that code unless its an auto computer and im...

i think i blew my fan motor up its flex lite fan that i got from a buddy and it work for about 2 months now it wont turn on i already replace the relay and tried hot wire it stright to the battery but all it does is click click click and wont turn on. the only think i could think of it broke...

i put this flex lite black magic fan on my car ran great till now only drove my car a little bit and had the fan 2 months bought from a friend now it crap out. first started when i put my intake on and touch the power battery post and burned the relay out got a new relay and it wont even turn on...

reply was in a parking lot and all most got caught the the park distict. i think the van was rocking to much the center consol suck in mustang too ass up head down if you know what i mean

just drop a 100.00 for a hotel to have sex in damn im stupid

reply yeah i turned the set screw on the throttle body. would the tps being at 1.23 volts would that matter

reply if it was o2 sensors wouldnt it idle like that all the time it only does this when its cold. could i need a msd box. im running trick flow intake cold air induction full exhaust timing at 14 degrees blaster coil 9mm plugs msd cap 3.73 gear. my check engine light never comes on dont...

ok i got a rough idle when cold runs 1000 rpms to 500 rpms when cold i aready change iac and running a 180 stat. could oxygen sensor be the cause i dont think its a vacuum leak because it only does it when its cold my tps is at 1.23 volts. i change intakes to a trick flow street and a 70mm...

what is the differance in mass air meter i know one is 73 and the other is 76 i have trick flow intake upper and lower and cold air induction, 70 mm throttle body and the egr plate which one would be the best one to get

what size would be best for me i know c and l makes 73 and a 76 i have full exhaust. trick flow intake,cold air induction mass air conv,3.73 gear 70 mm throttle body help me out

yeah mine too mine does the same thing it really piss me off i cant figure it out yet unless the gauges are crappy

ok does the fuel reg line the red wire that attaches to the top of reg to to the map sensor the box that sits on the top of the firewall. i pull mine off and now i didnt see where it came off of boy i need help :shrug:

reply towards the back of the motor. on the back theres a thing like a reg thats goes to the fuel rails i pulled the wire off both ends came off one sits on top of that reg and im not sure where the other wire plugs into that is a red wire maybe its a vac line

doing an intake swap.pulled the line on the fuel reg the red one off and the bottom came with it where does this wire go :mad:

do i need a disconnection tool to take off the fuel line when i put my new intake on