Search results

  1. I

    Progress Thread Ike34's Build Thread

    I haven't been on in awhile but was going through some things and noticed I never posted completed photos I found some old ones too!! This is when I bought it years ago!
  2. I

    Progress Thread Ike34's Build Thread

    I got my new setup tuned by Bob Kurgan today 472HP and 500TQ 89 Mustang Bob Kurgan Dyno Tune Karl Performance - YouTube 89 Mustang Bob Kurgan Dyno Tune Karl Performance - YouTube
  3. I

    Progress Thread Ike34's Build Thread

    Its running finally! 89 Mustang Supercharged 347 - YouTube I need to gets some pics up too of the motor installed.
  4. I

    New Build Starts And Dies

    I got it fixed and running, it was all my fault and had nothing to do with what I had thought. When I tucked and moved my wiring, I replaced my salt and pepper shakers with newer 10 pin connectors. Well it must have been one of the long nights I should have stopped working because I had some...
  5. I

    New Build Starts And Dies

    Thanks for the info. I went through it and have come closer to a conclusion. When I first started testing I had weak spark but then I lost it. Noid light does not blink across coil. Checked PIP signal with noid light, noid light blinks. Verified injector pulse with noid light, light blinks...
  6. I

    New Build Starts And Dies

    I just got everything put back together last night on my new engine and went to start it and it starts and runs for a few seconds and dies almost like ignition was switched off. I did not change anything from the last time it was run but that was 2 years ago! Info on what Ive checked: moving...
  7. I

    Progress Thread Ike34's Build Thread

    Some Progress Powder Coated and Polished Parts
  8. I

    Progress Thread Ike34's Build Thread

    Thanks, Its POR15 chassis coat black, I wanted something durable that I wouldn't have to worry much about and that I could do myself. This is my first time doing any body work or major painting. MikeH686, I went an measured them, they are roughly 11.5 inches
  9. I

    Progress Thread Ike34's Build Thread

    Thanks, Im not sure, Ill try and go measure later
  10. I

    Progress Thread Ike34's Build Thread

    I got my universal Griffin radiator mocked up and mounted and wired my contour fans and flexalite controller.
  11. I

    Progress Thread Ike34's Build Thread

    Thanks, I pieced everything together, If you have any questions Ill try and help.
  12. I

    Progress Thread Ike34's Build Thread

    Small update: Cobra brakes installed, waited to be bled when the girlfriend gets off work!
  13. I

    Progress Thread Ike34's Build Thread

    Slow going but making some progress Got the fenders and front bumper re-installed and installed new headlights Front tire fitment, 275/45 nittos, they were on the wheels so I tried them! they stick out a little far! Swapped one to a 245/45 today to see the difference. Much better...
  14. I

    Progress Thread Ike34's Build Thread

    Started getting the wiring ran and wrapped up Started modifying a mach 1 chin spoiler to fit.
  15. I

    Progress Thread Ike34's Build Thread

    some progress, got brake lines finished up and dash installed
  16. I

    Progress Thread Ike34's Build Thread

    Im going to have the fuel, boost and an AEM A/F on the A pillar and the oil, water and an intake air temp below my radio.
  17. I

    Progress Thread Ike34's Build Thread

    SpeedHut Gauges arrived today
  18. I

    Progress Thread Ike34's Build Thread

    93 Cobra Booster, wiper motor, throttle cable, speedo cable, firewall adjuster, MM steering shaft installed Wiring installed for AEM Meth controller and MSD 6AL2 to be installed under the drivers seat Wiring ran for gauges My next task My wiring diagram for all my add on wiring
  19. I

    Progress Thread Ike34's Build Thread

    I forgot about putting LEDs in the HVAC controls. I put 2 from the LEDs I had left over in them.