Search results

  1. B

    gt 40 head questions

    I have a set of gt 40 heads that have been stg 2 ported intake and exhaust and i was wondering if i can get bigger valves for them i was thinkin 1.94 and 1.60 or 2.02 valves will the valves fit these heads or will i have to stay with the stock valves.
  2. B

    front coil over

    What do i need to do to convert my stock 92 front suspension to a coil over on the front that is setup for drag racing?
  3. B

    what tires

    MOstly a weekend and track car with pony rims i was wondering what the best all around rear tires was for the car? dont really care about mileage from them.
  4. B

    msd ignition

    I am going to carb and i was wondering where is the best place to mount the 6al box? pics please
  5. B

    fuel line

    what is the size of the stock fuel line of a 92 mustang
  6. B

    msd ignition?

    Can you just hook up the wire that goes to the ignition switch to a toggle switch or will it cause problems? I am asking this bc i am going to a carb and took out the stock computer harness.
  7. B

    Who here has used the Trick Flow smog hole screws for cyl heads?

    they worked for my afr 165's fine no problem at all.
  8. B

    fuel cell

    I am going to carb and going with a rci fuel cell. Does it need to have foam insert or does it make a big difference not to have the foam?
  9. B

    ignition ?'s

    I have a 92 mustang and i am converting it to carbed. I have already taken out the stock computer and i was wondering what wire is the ignition wire in the engine bay to hook up the msd ignition into? thanks
  10. B

    what pushrod

    I have a 92 mustang and i am putting gt 40 heads from a 351 on the stock 302 block I need to know if i need the pushrods that fms has which are for a 302 with 351 heads Part # 397-m-6565-n332 from jegs? are these the pushrods i need? or will the stock ones be fine?
  11. B

    roller rockers qustions

    I have the pedestal mount fms roller rockers and i am bolting them to a gt 40 head that has been milled but only one will not get tight the pushrod is a little loose. Do i need shims for all of them or just that one and what is the part #. Thanks
  12. B

    putting on new heads

    I am installing new heads and do I need to clean the block of oil where the head gasket meets the block?
  13. B

    going carbed

    I have gt40 stg 2 ported heads, bbk 1 5/8 long tube bbk headers, trick flow stg 1 cam, victor jr intake, and a holley 650 dp. I am goin to put a fuel cell and i was wondering what pump and lines are needed to complete a new fuel system?
  14. B

    fuel system

    I am goin to carb from efi i have a victor jr intake gt 40 stage 2 ported heads, and a trickflow stg 1 cam with 1.6 roller rockers and bbk long tube headers. What fuel system is recomended for the new setup such as fittings and fuel pump, hoses. thanks
  15. B

    header studs

    are header studs worth the money or is the regular header bolts better to use with gt 40 heads and bbk 15/8 long tube headers?
  16. B

    what head bolts

    I have got new gt40 heads that have been heavily ported and I was wondering what arp head bolts i will need to bolt them to a 92 mustang with stock 302 block? thanks
  17. B

    smog holes in the back of heads

    What bolt or what plug will fit in the holes in the back of gt40 heads?
  18. B

    how to tell if there is a bent valve

    I have just got a pair of gt 40 heads that have new springs and a valve job. Before i put them on I want to check If they have bent valves or anything so i dont have problems after i put them on? Is their anyway to tell before i put them on the block? thanks
  19. B

    What bolts

    arp part #'s please
  20. B

    What bolts

    I am putting fms tall valve covers and i was wondering the size of the studs i will need? I am also putting a new victor jr intake and i was wondering the size of the intake bolts. What size are the bolts for the headers to the heads they are gt 40 ? thanks
Top Bottom
Back
Forums
Menu