Search results

  1. D

    RPM Shift Point Recomendations........

    i would set my shift light at 5400. by the time you react to the light you'll be 200 rpms higher and at the peak of your HP level. if you got some pretty high (numerically) gears then i may opt. to shift a little sooner than 5400. that way you can get to the next gear quicker to increase your...
  2. D

    i think my computer is toast.

    i have been defeated! im totally discusted....im takin it to--->????
  3. D

    i think my computer is toast.

    i dont think so. i know it was a 4 banger though. im heading over to the shop to bring it here. be back i a lil bit to test the previous post. i was looking at the diagram above. the grey connector i plugged in on the clutch switch is tied in with the SIGRTN (black/white) to all of the...
  4. D

    i think my computer is toast.

    93 5.0 lx- gt40 intake, 70mm TB, TFS-1 cam, exhaust. i had 24# inj and MAF on it but took them back off for the stockers so that is one less variable. i switched my computer out with a known good one and nothing changed. this all started when i ran codes and got 67 (KOEO). i plugged the...
  5. D

    i think my computer is toast.

    i went by the shop but only had like 10 min. to check some stuff you asked for. i unplugged the TPS connector and checked the 3 prongs on the main harness connector. i used the DMM's black lead as a common ground. i checked with the DMMs red lead to the TPS connectors black wire (4.86v), green...
  6. D

    i think my computer is toast.

    ill see what i get and let yah know. thanks for your help.
  7. D

    i think my computer is toast.

    IDK? that is why im posting here....im looking for help. the TPS is new.
  8. D

    i think my computer is toast.

    oops
  9. D

    i think my computer is toast.

    the 10 pins were cleaned and regreased. im trying to pull codes with a scanner. the prev. owner did something to the CEL because "he didnt want it to come on anymore." so using that method is going to be hard. the tps is getting 5v on the orange wire but nothing on the green. when all this...
  10. D

    i think my computer is toast.

    the computer is fine. switched it for an A3M and its doin the same thing. not sure about the ground put the soucre wire is getting 5.03 v. when it test the green and black wires i get 0.00 .
  11. D

    i think my computer is toast.

    i may have fried the computer while messing with the tps/idle or it crapped out on me. irregardless, the car will cold start but dumps alot of fuel while driving. if i cut it off while hot, it dumps fuel in comb cham. while it turns over but doesnt start, and will not start. im showing 0.00 at...
  12. D

    ran codes to see what's up.

    ok will do. thanks for your help over on corral. also i think the scan tool spit them out in the order i gave. ill check today for insurance.
  13. D

    ran codes to see what's up.

    the smog pump and related "stuff" was deleted when i got the car. the EGR has a vaccum nipple with no line attached to it. what needs to be done about that? what codes from above will i be getting due to the stuff being deleted? how do i fix the codes to make them go off? should i jus live with...
  14. D

    ran codes to see what's up.

    since i bought the car it has had a idle surging problem. i ran codes today to see if i can shed some light on the situation. the car is a 1993 4 cyl to v8 swap, 5 speed, tfs-1 cam, gt40 intake, exhaust, 24#, MAF, 70mm TB. it was surging before and after i swapped the aftermarket stuff. (it was...
  15. D

    275/40 on 18x10 rim

    holy crap. no rubbing? did you accomplish that by rolling lips, cutting pipes, and BFH?
  16. D

    275/40 on 18x10 rim

    thanks for that link. im prob jus gonna go with some 275 40 18 to be safe. will 275 fit right on a 10 wheel? I don't want them to no be wide enough and barely fit on the rim.
  17. D

    275/40 on 18x10 rim

    what did everyone else do to the rear to ge the bad boys up in there? rolling lip, flipping quad, BFH......that kinda stuff. could the possibility of 285's exist?
  18. D

    rear suggestions please

    surprised the rear is still intact with those number
  19. D

    Enginge Formula 4 a high 6 to low 7 second 1/8th small block?????

    parts + labor + traction = 7000
  20. D

    aluminum driveshaft for 1991

    I traded a metal scrapper my totaled coupe body (jus the hull) for a saleen wing and an alum. DS. wasn't too bad of a deal if you ask me
Top Bottom
Back
Forums
Menu