Search results

  1. Markus

    little preload on master cylinder with hydroboost?

    Hello guys, i have looked on a 2000 mustang gt. The preload is normal. thank you for reading. Markus
  2. Markus

    little preload on master cylinder with hydroboost?

    Hello guys, today i have changed the master cylinder on my 2003 GT and i noticed that i have little preload on the master cylinder. About 0.04-0.05 So i checked this on my old (stock) mc and there is the same preload. Is that correct with hydroboost brakes? thank you Markus
  3. Markus

    Nu-relics Power Windows

    today i have answere my question myself. The nu relics power windows kit do NOT fit with a 67 mustang deluxe door. The window motor interfered with the door speaker. My speaker, a low profile Alpine, is about 1 - 1 /1/2 inch too deep. I fliped over the window motor (left to right and right to...
  4. Markus

    Nu-relics Power Windows

    i like them too but they horrible expensive :nonono:
  5. Markus

    Nu-relics Power Windows

    yes i from Wittlich, 15 km from air base Spangdahlem. I ordered the nu-relics power windows and hope that they will fit. I do not use the crank switch. I use the billet modular switches from watson´s streetworks for the center console. Markus
  6. Markus

    Nu-relics Power Windows

    Hello guys, i have the idea to install nu-relics power windows in my 67 fastback. I´m afraid that i have space problems with the deluxe doors. Interference windows motor and speaker. Have one of you experience with this power windows and the door speaker and courtesy lights? My door speakers...
  7. Markus

    C4 Shift Improver Kit Question

    Hello guys, next weekend i like to install a b&m shift improver kit. My 68 Mustang is a daily driver and weekend cruiser. Now i don´t notice the shifts. It shift very very smooth. The transmission is rebuild. I like more firmer and crisper shifts. My question is, should i choose the stage 1 or...
  8. Markus

    67 Mustang Fastback Walk Around

    Hi guys, on sunday i took a little time to film my car. Here is the result. walk around my 67 fastback Attention, the complete file is very big !! thank´s Markus
  9. Markus

    m-2300-k brake kit

    I use this kit on my 67 mustang with a 8.8 axle. In fact the NRC brackets are much thiner than the ford brackets. I modified the anti moan bracktets to work with the NRC and no noise or rattle. I drive a few years now, no problems at all. Here in my link you can see those brackets side by side...
  10. Markus

    Hood Hinges

    I bought a set of these dynacorn hinges and i´m very pleased. They are indeed so much thicker. And i am certain that the hood opens wider than with my old ones. All my alignment problems are gone and the hood sit fantastic. Here are two pics to compare original vs. mustangs unlimited vs...
  11. Markus

    Intake Flow Numbers ?

    Hello guys, in the next days i start with a new project. At the moment i have a gt40 tubular multi point efi on my 331. Now i convert to a msd atomic efi tbi. I use for this a weiand stealth intake manifold. In the past i thought that my gt40 lower intake was the bottle neck. Do anyone know...
  12. Markus

    Fe And Tremec 5 Speed Question

    Hello SoCalCruising, i have the problem here in germany with the TÜV. The car must be vintage correct. That mean my 331 stroker with efi is not and a 351 ist not correct too. So i like to go with a big vintage correct engine in the future but not a simple 390 fe and no 428. Both are too heavy...
  13. Markus

    Fe And Tremec 5 Speed Question

    Hello guys, i run a 331 with an "old" 3550 tko for years now. The transmissions have a long (7.2 inch) input shaft. In the near future i like to convert my 67 fastback to a big block car and like to reuse the transmission with a quicktime bellhousing. Here is my problem. I´ve heard that i need...
  14. Markus

    Is 24lb Injectors Good Enough Or Do I Need 30s?

    I run 24lbs with my 331. The duty cycle is 80-85 % with 50 psi fuel pressure. I´m change to 30 pounders. So i think the 24 lbs injectores are not sufficent for your application. Markus
  15. Markus

    borgeson steering done!

    I run a KRC steering pump for my borgeson box. The flow and the pressure is changeable between 1200 psi - 1450 psi and 1.05 gpm - 3.17 gpm. I also run a hydroboost brake booster so i need more flow and pressure that my stock steering pump can hold. I use a pressure relive valve for 1200 psi and...
  16. Markus

    AFR 165 & 185 users... any issues w/ rocker arm positioning?

    The isky plates we use are this http://www.summitracing.com/parts/ISK-200-AGP/ You must grind the guide plate to clear the push rod. With out grinding it looks like this one http://212.227.100.192/mustang/mods/isky2.jpg To compare the afr and the isky http://212.227.100.192/mustang/mods/isky1.jpg
  17. Markus

    AFR 165 & 185 users... any issues w/ rocker arm positioning?

    same problem here. I fight with this problem since 5-6 years now on my 185. The passenger side is "ok" but the driver side is crap. I use isky guide plates from day one. With AFR guide plates no chance. My biggest problem is not only the side to side alignment. The studs or the valve guides on 5...
  18. Markus

    photo shooting for a magazine

    Thank you guys, if you are interested here all mods in a overview http://www.mustang1967.de/overview.html and a happy new year !! in 6 hours the old year is gone here Markus
  19. Markus

    photo shooting for a magazine

    Thank you guys for the replies.:) Gene i know the magnums are wrong but they are my favorit looking wheels. :rolleyes: Markus
  20. Markus

    photo shooting for a magazine

    Hello guys, my car was in november in a us car magazine called "street" here in germany. I have done the pictures online. http://212.227.100.192/mu...allerys/Street/index.html i wish you a happy new year Markus
Top Bottom
Back
Forums
Menu