Search results

I am thinking about trying to sell my car but I don't know how much to ask for it. It is a black 5 speed 95 GTS. Interior is in good shape. The out side needs a paint job because ford paint sucks and it is starting to oxidize. I don't really want to try and sell it on ebay because I think I...

I was going to relocate my battery and mount the msd there, but after reading the rules I decided not to do that. I would really like to mount it in the engine bay, but I can't find a place with enough room to mount it. Let me know where you have your msd mounted.

I bent a couple of push rods so I did a compression test to see if the valves might be bent. The cylinder that had the bent push rods read 195 lbs and the highest cylinder was 205. I know stock should be between 130-160. My heads are afr 165 with a 58cc chamber. Would this be why my cylinder...

I have to order new push rods and new lifters for my car. I have to spend $500 with summit to get 0% for a year. I figure the lifters and pushrods will run my about $200 so I have to spend at least 300 more. I am thinking either a steel or aluminum flywheel, or a mds 6al ignition. With my...

I was running my car last night when it started making a awfull knocking noise. The car was firing back through the intake runner on the number 4 cylinder. It bent the exhast valve on #4 real bad and it also bent the intake, but the intake was still opening enough for the air to fire back out...

I was out running my car tonight and I got it too about 5000rpms in third gear when something let loose. It sounds like something is hitting the valve cover on the passengers side. I took off the upper intake but I was to tired to go any farther. When I turned the motor over the last cylinder...

I just bought a new lighning. How many miles do I need to go before I can hammer it? Do I need to change the oil at 500 or 1000 miles? I had a saleswoman and she told me that all that would be in the book, but the service book just says to change the oil every 5000 miles. If it wasn't...

Which intakes will clear the 87-93 valve covers on a 95 mustang without using the 1/2 inch spacer. I have a cobra intake now but I have to use the spacer with it because the egr hits and the vacuum pipe on the drivers side hits. I want to keep my stock hood so that is my problem with running...

does anyone run this intake yet? The numbers I saw in 5.0 mustang were pretty impressive. I would like to know how it does as far as low end power. I drive my car on the street a good bit of the time. Maybe someone could tell me if it would work good with my set up. It will be replacing a...

When I drive my car normal I have a slight hesitation. When I get on the gas its accelerates with no problems. I just put a MSD distributor and new injectors in and that did not help. I think I might have a collapsed lifter and I was wondering if that might cause it? When I pull my upper...

I have a chance to purchase a powerdyne for a grand. The only thing is that it is on a 89 mustang. Is everying thing the same set up for my 95 except for the itake pipe or is there other differences in the kits? How much will it cost me to make this kit work for my car. It is a 9 psi kit...

I have just pulled my valve covers off of my car. My rockers have been clacking and making noise. Can someone tell me if I am right or wrong in my thinking. If I tighten the nut on my stud mount rocker arms to the point that the pushrod will not spinn and then I give it my half turn while the...

I have a set of stud mount scorpion 1.6 roller rockers on my heads. I just put the heads and rockers on and drove around on them for a couple of days. I had a little bit of valvetrain noise so I went back in and I adjusted the rockers again. The first time after I installed the rockers I only...

I just got done installing a set of afr 165s and I wanted to go try out the car. I called a buddy of mine with a 89 notch with everything trickflow. We raced a few times on a back road then we parked the cars for a little while. As we were sitting around a black AMG E55 pulls up. I knew I...

I just picked up some afr 165 emissions legal. I need to know if I can block the smog passage with a brass plug or if I need to get a special plug. If it takes a brass plug what size is it?

I need to know if the b303 in my moter will let the heads breath enough or if it will hold me back from making the power I should.

I am about to be installing a set of AFR 165 heads on my car. My problem is what valve covers do I use. I am running a cobra intake. A lot of the aftermarket valve covers say that you need a one inch intake spacer to clear the tall valve covers. I know that some people use 87 to 93 valve...