Search results

  1. 5

    Q's about cat converters

    Does anyone know where I can find a used set of catalytic converters (2 separate, no h-pipe), for under $25 (doesnt need to be pretty, just want the casings to punch out for inspection), or does anyone know a way to get around the inspection with not cats? (visual inspection, not emissions).
  2. 5

    Well, now I've gone and done it...(Important Questions)

    I'd say t56, you'll probably gain a little more torque, along with some top due to the sixth gear. The bad thing I see is loosing some acceleration time due to another gear, but if you are good at speed shifting, no worries. They go for about $1800-$2200 I think.
  3. 5

    Confused, what is best way to wire up in-line fuel pump?

    My 88 cougar motor to 84 stang body is pretty much complete, I just have to figure out how to wire up the fuel pump. Since the 84 motor had a mech. pump, and I got a deal on a Holley Red in-line pump, I decided to put that on, (thought it would be easier). I need a quick crash course on...
  4. 5

    Help! How to remove distributor drive gear?

    Sounds like a lot of tools that I dont have the money for right now. What kind of auto store should I take it to? (this way if they screw something up, I wont have to dish out more money).
  5. 5

    Help! How to remove distributor drive gear?

    So what kind of puller do I need? Is it the one that has two teeth and looks like a champagne bottle opener?
  6. 5

    Help! How to remove distributor drive gear?

    The pin goes straight through. It looks like the gear might be threaded on (84 dist., havent pulled the 88 dist out yet), I need to know how to remove the gears. Certain tools? Certain methods?
  7. 5

    Help! How to remove distributor drive gear?

    I am going to put the 88 dist drive gear on my 84 vaccum advance dist, just so that I know the dist will work with the 88 roller cam. I can get the pin out, but I cant remove the gear is it threaded on? Pressed on? How do I go about removing it?
  8. 5

    WHY NO SEARCH

    I was wondering the same. lib88stang, where in PA do you live, I am located near State College.
  9. 5

    Installed Maximum Motorsports Strut Tower Brace, Very Pleased

    What does it do? Help with cornering? Stability?
  10. 5

    Trouble! Cant remove upper intake plenum, and misc Q's

    Is it hard? Will I need a special tool? (tranny was originally auto)
  11. 5

    Trouble! Cant remove upper intake plenum, and misc Q's

    Guess I'll have to buy, or borrow some. Do you know how to install a pilot bearing?
  12. 5

    New member need some help

    My 3.73's get decent gas mileage, (better than my dad's 2.5 jeep wrangler), and they up the performance quite a bit.
  13. 5

    Trouble! Cant remove upper intake plenum, and misc Q's

    Alright, I still would have never guessed the bolts were under the plaque, felt like it was still bolted on, but couldnt find them.
  14. 5

    Trouble! Cant remove upper intake plenum, and misc Q's

    So my motor is an H.O.? The plaque says 5.0. efi
  15. 5

    Who sells GOOD Starter Relays????

    Check www.50resto.com good parts with good prices
  16. 5

    Trouble! Cant remove upper intake plenum, and misc Q's

    I am in the process of switching an 88 cougar over to carb, and I cant get the stock efi upper intake plenum off. The plenum will move clockwise and counter clockwise a little bit, but thats it. I removed the four bolts, thats all I saw, is there more? What size belt should I use to bypass...
  17. 5

    Need torque specs fast

    What are the torque specs for a 10 inch flywheel?
  18. 5

    Tranny Swap Help

    I cant see why you couldnt, you may need the bellhousing also. The gearing is probably set more for cruisin than performance though.