Search results

  1. Tubo(2-bo)

    For Sale: AFR 165's, Ported Performer, FTI Cam, Etc.

    I got the heads, PR's and headbolts. Prolly still has the rest. Send an email as he doesnt check the classifides often.
  2. Tubo(2-bo)

    FTI cam for sale

    Plz email or contact me. I'm intested. Building a 331 to go with my EFI, AFR 165, 4R70W, 1965 2+2....need cam
  3. Tubo(2-bo)

    BBK 70mm Throtle Body

    If, $50 shipped to 32548 I'll take it
  4. Tubo(2-bo)

    New in the box! High Torque Mini Starter fits 5.0-351w with T5, C4 AOD

    I'll take it. PP sent. Thank You. Tubo
  5. Tubo(2-bo)

    xe 266hr12 $130 shipped

    Check PMs
  6. Tubo(2-bo)

    For Sale: AFR 165's, Ported Performer, FTI Cam, Etc.

    Let's make a deal. contact me, corky.p at cox.net
  7. Tubo(2-bo)

    AOD and AODE

    Say Nick??? Did you get any comparitive times, on your, car stock AOD gears vs wide ratio gear set??
  8. Tubo(2-bo)

    reccomend a master cylinder

    +1 On the MustangSteve kit. I've had his kit in mine for 5 years, no worries. I do have the Granada discs, but several Stang'ers use the MS kit with 13 cobra discs & calipers.
  9. Tubo(2-bo)

    CAM SELECTION--NEED ADVICE

    The Dang 351 would have been my first choice any way. 'specially as the Coug is heavier and has the room to acomodate, the slightly larger 351. That Anderson cam will do fine in the 351, too. As your getting the new springs, double check & get ones spec'ed to match the cam.
  10. Tubo(2-bo)

    Mini starter conversion.

    The fox body fender mounted solenoid has a diode in it to prevent the starter from "hanging". I copied Ford & replaced my fender mount solenoid with a Fox body type.
  11. Tubo(2-bo)

    AOD and AODE

    The bellhousing on the AODE/4R70W's is 1in deeper, other than that they are externally the same. DS 1in shorter & Tranny mount to accomodate.
  12. Tubo(2-bo)

    Which overdrive tranny fits a 66 w/o cutting?

    Yes I'm using a Baumann TCS. Other than using different tailshaft housings(interchangable) and yokes, the AODE & 4R70W are essentially the same tranny. The TCS integrates very well with my EFI. It is compatible with carb too, you need to use a TPS on the carb. I have recently installed a...
  13. Tubo(2-bo)

    engine sizes

    You might find yourself to be a ground breaker, doing a conversion rarely if ever attempted by anyone else. IIRC the 4.0 shares a bellhousing pattern with the modular 4.6, tranny & fuel injection unique to that family would need to be used. Another more commonly done conversion may be a...
  14. Tubo(2-bo)

    Edelbrock Pro Flo XT What Are Your Thoughts?

    I'd think unless you want a"old school" look for a show car or have an engine not readily adaptable to EECIV, you'll be much better off sticking to ECCIV. Buy a harness from fordfuelinjection.com, using hardware like I have is easy to find. All the foxbody guy's have already tested every part...
  15. Tubo(2-bo)

    Which overdrive tranny fits a 66 w/o cutting?

    AODE/4R70W's are 1 in longer than an AOD, because the bell housing is 1 deeper, otherwise the exterior dimension are exactly the same. There are tabs on the body of the trannys that can be trimmed off to give a little extra clearance. Tabs are used to hold the tranny body in the machineng jig...
  16. Tubo(2-bo)

    from scratch, shortblock, longblock, or crate

    I have a block in the machine shop now. I was going for just machining, and I'd do the assembly. But the shop will install the rotating assly about as cheap as I can buy rings & bearings, well close any way. So I'll pick up a very short block & install the cam & timing set myself. Real good shop...
  17. Tubo(2-bo)

    JBA Headers Fitment Issue

    Not tuRbo,:) I know what you mean about too pricy fer the RJM mounts, a fellow Stanger made me a deal on them. Prolly wouldent have gotten them otherwise. The RJM's did allow me to move the engine closer to the fire wall, which is what was needed for my pair of JBA's to fit well, also helped iin...
  18. Tubo(2-bo)

    JBA Headers Fitment Issue

    I had to use RRJM adjustable mounts, to find the "sweet spot" for mounting my 1650's. Once there they're perfect. I was ready to commit mayhem long before I got the RJM mounts.
  19. Tubo(2-bo)

    8" Axles shaft length - HELP TODAY

    With enough splinage remaining, you can cut or grind the .25 off. File bevel each spline end, good to go. Kinda shade tree, but it'll work.
  20. Tubo(2-bo)

    Need some EFI recommendations

    What Tranny? rear tires/wheels are on the car? Whats you 60' time? Traction limited? Havent had mine to the track, just curious.