Search results

I recently jusyt finished installing my new forged ported cammed pi 2v engine w p51 intake and i finally fired it up today. The problem is my alternator isnt charging the battery. I checked everything. The main wire is bolted up and the plug with the two wires is on. I have a electric water...

i am changing the mirrors on my girlfriends car and need to know how to remove the tweeter to get to the bolts to the mirror. Anyone know thanks

Seeing the 98's have the basket i know a few modifications have to be made for the pump to fit but what about the the filter thats suppose to be on the bottom of the pump it doesnt really fit in the basket what do i do about that

i have a 98 mustang gt with a 2002 gt motor in it. I've had the motor in for almost a year and the a/c worked fine. But when i took the car out this summer it started almost dieing on me when i turned the a/c on. It would not idle the car would go up and down from like 1000 rpms to 0 almost...

I have a 98 mustang gt and i recently put a 2002 gt motor in when i pulled the old motor i left the drive shaft connected and just slid it off the shaft. When i dropped my new motor in i didnt slid the driveshaft back and i already bolted everything together added all the fluid and connected...

Im puttin a 2002 gt engine in my 98 gt and i need to tap into the aluminum crossover on the new engine because the 98 has to sensors. I was wondering if i could take the cross over off my 98 intake and put it on my 2002 engine without causing any problems?

I was pulling my motor today in my 98 mustang gt and i disconnected the tranny and i was puling the motor and it got stuck on something to find out the flywheel was hitting the starter so it would come out. I tried disconnecting the starter but i can only get to the 2 visible bolts the other one...

I have a 98 mustang gt and im pulling the motor and im almost all set to pull it but i want to disconnect the tranny and just pull the motor. How Can i unbolt the top of the bellhousing? It seems to me that i cant get at the bolts. Any help would be great thanks alot

bbk sells full length headers are these their long tube headers or do they have long tube headers. Info would help

I have a 98 mustang gt but im getting a 2002 gt engine. I want to install longtube headers in the process of the motor swap. I was gona get macs but i read there no good so i was thinking bbk longtube. Anyone got any websites where i can get these. Wheres the cheapest to get them. Are there...

im going to be switching my 98 mustang gt engine soon for a 2002 engine and i was wondering if there was any websites out there aiding people on doing this.?

I have a 98 mustang gt and i want to swap the engine for a 2003 mustang gt engine and was wondering if everything would work out. I was going to just do the pi swap but my engine burns oil and i want a low mile engine. Also im going to supercharge it later and dont want to worry about...

i did horrible at the track the other day and was wondering when i should be shifting in my 98 mustang gt

Basically i had a tko500 installed in my 98 mustang gt and was wondering if it helps my quarter mile times at all.

Does the tko 500 come with a short throw shifter or would it benifit from a steeda tri ax

I have a 98 mustang gt and i need a new transmission i heard the tko's were good but dont know which one would be a good choice for me. I have the following mods 4.10 gears pullies trickflow upper intake 70mm tb ram air K&n air filter centerforce clutch flowmasters 40 series 2 1/2 "...

i have a 98 mustang gt with 4.10's in the rearend i want to put a t56 that is from ddperformance.com and was wondering if the gearing was to much for my almost stock mustang. the gear rations are 2.97/2.07/1.43/1.00/.80/.62

I have a 98 mustang gt and my t45 went to *****. I wana get a new tranny that has beter gear ratio's and one that can handle more power. I was even thinking about the t46 but thats really pricey. Are there any really good trannys out there for a affordable price. If so where could i get this...

with these mods what do you think my hp would be around at the engine 4.10 gears pullies ram air with k&n air filter Centerforce clutch trickflow upper intake 70mm tb 9mm spark plug wires 2 1/2 exhaust flowmasters with non catted X pipe soon to be installed ------- 99 pi heads...

I have a 98 mustang gt with 70,000 miles on it. I had a new centerforce clutch put in like a year ago. The car runs great but the transmission is the problem. Last summer the car started grinding third gear alot. After i installed steeda's short throw shifter that went away and after awhile...