Search results

  1. C

    shadyside

    Starts at 5 or 6 on Thursday nights and goes until 10. On Sunday starts at 1 until 5 or 6.
  2. C

    Dyno Day results

    I am going to give Tim a call tomorrow. Does anyone have the number off hand? Brandon (Z28) I have to sell mine before I can take your advice bud. I have already looked at the auto trader for some possible ideas.
  3. C

    MOVING TO GREENVILLE, SC

    ITT is a great school my best friend went there after we graduated HS. They are rigt you will see a large number of Beamers. Congrats on the move Greenville is a nice place to live.
  4. C

    Dyno Day results

    This did not go as well as I had hoped. I had seen others on this board pull well over 300 with similar setups. 1st run 221.5hp and 289.6tq, 2nd run 224.2 and 292.6tq. After these numbers I did not even pull a third time. At 4000 rpms the A/F goes under 12.1 and at 4400 it goes off the chart...
  5. C

    99 engine swap into 96 GT

    First of all what kind of hp gain can I expect from this swap with the mods in sig? Next how difficult is the swap it self? Has anyone done this what are some of the little problems that you ran into? I am getting this motor dirt cheap. Should I rebuild the motor before installing it? It has...
  6. C

    Anyone in the NC/SC area up for a meet in the next few weeks?

    Thanks for the directions if we can't get more people the dyno may be cancelled. Either way I will try and make it.
  7. C

    Anyone in the NC/SC area up for a meet in the next few weeks?

    I am getting it dynoed early but the dyno is in Kingsport TN. I may try and leave from there an come down.
  8. C

    Dyno Numbers.. Finally

    I hope to pull very similar numbers when I go to the dyno on June 12th. Which pulley do you have?
  9. C

    Anyone in the NC/SC area up for a meet in the next few weeks?

    I would be very interested in coming as long as it is not on the 12th getting the stang dynoed that day. BTW I had a 98 and 01 SS awesome cars ( the 01 was also on the juice).
  10. C

    personal plates!!

    Venomus
  11. C

    Tensioner pulley ?'s

    I think the bearings in the pulley have gone bad is this a possibility? Does anyone know where to buy a new tensioner?
  12. C

    Tensioner pulley ?'s

    I found the reason that I continue to eat belts. The belt is riding off the tensioner an rubbing against the block. Can you adjust this or is it set? Has anyone else had this happen? What can I do to fix it? Thanks guys for any help
  13. C

    Chopping Factory Springs

    I cut mine to get a 2" drop and the car does bottom out. The ride quality is not much worse than my 97 Cobra with BBK springs. If you do cut them be sure and order some C/C plates or you can kiss those front tires goodbye.
  14. C

    Need hints on installing new plenum and TB

    I got the 10mm socket anything else? What do you use to clean the IAC?
  15. C

    Need hints on installing new plenum and TB

    Thanks for the info guys. 2Slow96GT what part of SC are you from?
  16. C

    Need hints on installing new plenum and TB

    Got any thing to make the swap go smoother? The new ones are suppose to be here Friday.
  17. C

    Supercharged plug ?'s

    I'll do that thanks. Those TR55's sure got hot after just 2 miles last night :bang:
  18. C

    Supercharged plug ?'s

    Got the TR6's in the car today thanks for the help
  19. C

    Supercharged plug ?'s

    I already had them from a car I owned before that I never got to install them in. I will take them back out tomorrow and buy some TR6's should I use the same gap? Thanks for the heads up I am still very new to this kind of issue. If I cannot get TR6's does anyone know the Autolite or Champion...
  20. C

    Supercharged plug ?'s

    Went ahead with the NGK TR55's at .035. Thanks for the info.
Top Bottom
Back
Forums
Menu